Click below to subscribe to the Beginner's Cheats Season 5 column to watch 50 episodes including this one
This is a country road, on the left is a green wheat field, on the right is a peach orchard where peach blossoms are blooming, and there is a train passing on the railway in front, the scenery here is very good, but because the culvert intersection in front of it is blocked and cannot be passed, you need to find a place to make a U-turn on this road.
Visually measuring the width of this road is about three meters, the road surface is paved with cement, the left and right sides of the road and the farmland have a gap, then it is difficult to make a U-turn on the road surface, and now you need to find a slightly wider position to complete the U-turn.
Now I see a path to Taoyuan on the right, and turn right with a little slope, but the path forms a T-shaped intersection with the cement road to see if this position can be used to make a U-turn.
Now get out of the car to check the terrain, the wall of the taoyuan is surrounded by barbed wire, and the fence at the entrance of the taoyuan is crooked to one side,
The road surface of the doorway is connected by a piece of rectangular cement board, the length of the cement board is about 1.2 meters, which is not enough for the width of the vehicle, the two ends of the first cement board near the road, it is estimated that this position can be borrowed on one side of the tens of centimeters, and there are traces of tire pressure on the ground, and other vehicles may also borrow the aisle here.
Looking inside, I did enter the garden through this cement slab.
On the left side of the road is a wheat field, and the bottom of the cement curb cannot be borrowed, and it is difficult for the tire to fall down.
Okay, so let's get in the car and try it out and see how to make a good use of this T-cross position to make a U-turn. The vehicle drives from the opposite side, hits the right and follows the right side of the road, and hits the left when the front wheel position reaches the intersection,
You can see the right front wheel close to the right curb and turn left.
Park your car sideways to the left. Pay attention to the right rear wheel or the right rear corner of the body, just towards the inflection point where the path intersects with the road T-shaped, and this inflection point is the direction of the right rear wheel when reversing backwards.
Hang up the reverse gear to start so that the right rear wheel reverses towards the inflection point, and when the right rear wheel is about to reach the edge of the inflection point road, hit the right direction,
Let the right rear wheel fall along the inflection point and stop when the right rear wheel protrudes out of the curb edge about 60 cm or so. Because the attention is on the rear wheel at this time, do not pay too much attention to whether to return to the direction when parking, the focus at this time is to let the rear wheel fall backwards as much as possible under the condition of ensuring safety, which can give the front wheel more room to turn.
Hang up the front gear to the left to play the direction, note that here is not to encourage the left to play the full direction, the focus is to consider the next step backward, the left rear wheel should be pressed to the path pavement, so that the next turn to the left, in fact, is to let the left and right rear wheels swap roles. At present, from the exterior, you can see that the left front wheel and the right rear wheel have reached a very close distance from the curb edge.
Hanging upside down the block to the right to hit the direction, the left wheel began to fall along the path, the right rear wheel retreated along the right limit edge, it can be seen that the height of the right rear wheel has begun to fall below the height of the left rear wheel,
This reversing car reaches the rear limit position and then stops in the positive direction.
Hanging forward gear to the left to hit the direction, the right rear wheel soon also opened out of the depression, into the road surface, because at this time in the car can not be observed and can not judge the exact position of the right front wheel, so when the right rear wheel into the road back to the positive direction of parking.
Hang up the reverse gear and hit the right direction, take a proper inverted step and stop back in the right direction, at this time the left rear wheel is on the path, and the right rear wheel is still on the edge of the road.
Hang up the front gear to the left to hit the direction, successfully achieve the limit narrow road to borrow the U-turn.
There are three difficulties in the U-turn of the T-shaped crossing: the first difficulty is that the road itself is very narrow, only enough to reach the distance between the front and rear wheels;
The second difficulty is that the path of the borrowed road is also very narrow, not enough for the width of a car, you need to take care of one side of the tire on the road, the other side is below the curb edge, three wheels on the hardened road, let a rear wheel down some is not a big problem, the front wheel drive vehicle can be brought out when it is driven forward;
The third is that the wheat field on the side of the road has a large drop from the curb edge, and it is not easy for the vehicle to accurately determine the position of the front wheel in the pendulum state, where there is no shoulder as a barrier, and if you drive more, you will fall directly.
With these three difficulties, he finally successfully completed the U-turn, focusing on the grasp of the rear wheel in the rearview mirror. I will show you how the rearview mirror picture is observed.
The first is to drive over and stop backwards to observe the right rear wheel. The vehicle drove along the right side of the road, hitting the left in the direction of the right rearview mirror to see the right rear corner towards the triangle of the T-shaped inflection point position,
Hang up the reverse gear and fine-tune the direction in the right rearview mirror to see the right rear corner fall along a little closer to the road surface, and stop when the right rear wheel presses against the path cement board.
Second, after completing the first reversing car, to the front car, to the premise car to be conservative, the front is not good to judge the distance then look at the back, as long as the rear wheel can be moved, the front does not have to be too limited, hang the front gear to the left to play the direction, in the right rearview mirror to see the right rear wheel to the road edge above the position to stop,
Hanging the inverted gear continues to observe the right rear wheel allowing him to reverse along the extreme position of the far edge until the back is almost pressed against the obstacle, at which point the vehicle is close to being perpendicular to the path.
According to the width of the car and the width of the road, the left tire is on the cement board of the path, and the position where the vehicle is now, whether the front can be turned out enough, and it cannot be risked. Hang up the forward block and go in the direction of hitting the left, first turn left,
Another one is more secure, hang the reverse gear to the right to hit the direction of reversing, properly reverse the car and hang up the forward gear in the left direction to successfully complete the U-turn.
Dear old and new friends, a total of 50 video episodes of "Beginner Cheats - Season 5" have begun to be updated