Overlord Cha Ji robbed the tomb.
Prepare paper bags: Dutch white card, a card holder, two prismatic films, glue sticks, wallpaper knives, scissors, paper rulers and handbook tape scrapers, and finally a cutting board. First dig out the head of this person in the paper bag. For example, today take Hanano as an example, cut it down along this white edge, so that you have a small card for the character.
Then cut the edge of the paper bag, which is navy blue. Use the small cardboard bag just now to mark the appropriate size, which is slightly smaller than the paper bag, otherwise it cannot be stuffed in. You can look at the size with the help of the horizontal and vertical lines of the cutting plate on the back, so that it is about the same. Then cut the width, long and wide.
With the help of the auxiliary line of the back cutting plate, it is cut out at a relatively straight right angle, and almost cut a little more edge. Because it will be thickened in a while, it will be slightly smaller than it is now. Take out the glue stick and apply it in a circle, there are protruding places around it that are not very symmetrical, don't care, you need to cut it open for a while, and then scrape it flat. This edge can be left alone, and you will have to dig it up later. If you are very mindful, you can use a splint to clamp it and flatten.
You can see that this piece is missing a hole, missing a hole to cut this place, or paint it, apply glue stick. Note that this place can not be glued, nor can it be replaced by double-sided tape, double-sided adhesive will leak oil upwards in the later stage, and the glue will become very wrinkled after use, just use this position to block the seam of the seal that was just deducted.
Then look at the side of this paper bag, which is actually six small yellow chickens of the protagonist, cut into a small thin strip, and also coated with glue sticks. After applying the glue label, aim at this position and paste it. Or scrape it slightly with a high-pressure knife to make it fit tightly, and use scissors to roughly trim the edge, so that the approximate shape of the small card will be there.
At this time, take out the cold surface film, this one is a new film. Cut it from the middle, put this film flat on this, spread the small card just now, and use this scraper to carefully scrape it flat, especially this position of the paper bag on the side just now. Scrape flat and get the front. Because there are two layers pasted here, it is not a flat surface, so a little force must be used here in the seam, and this force must be used evenly.
If your strength is stuck in one place, he will scrape this membrane, and use a little force where there is a bulge. The front of the small card is complete. At this time, trim the edges of it, or press it a little with a steel ruler, one size fits all, so that it will be more neat. When cutting, you must use force, the harder you cut out, the more neat, and then press this pressed hand must also be forced, otherwise he will run off.
Then fix the top and bottom as well. Try putting it in the holder and see if it's still a little bigger, but it doesn't matter if you'll trim it later. At this time, take out the Dutch white card just prepared, the Dutch white card is the kind used for rubber sheets, try to choose a softer one. Apply glue sticks on the front of the Dutch white card, this one should be applied evenly and a little thicker, otherwise he may open. Then stick it on and continue to scrape tightly, you can see that it has stuck more steadily, and continue to repair its edges. The left and right should be repaired a little more, because it has thickness and cannot be stuffed into that card film. Of course, if you don't need to stuff it into the card film, you don't need to continue to repair it, you can directly scrape off the excess white card along its edge.
Then at this time, you can cut off the seal just now, trim it a little and repair the blue background. Attach it to the back of the small card.
At this time, take out another dragon watch film just prepared, this dragon watch film is filament-sided, everyone buys the dragon watch film when dividing. Non-special needs must not choose glossy or glossy surface, but also cut in half, continue to flatten, turn over and continue to scrape it.
If you choose hot tin and try to choose a thinner hot tin film, you can use scissors to cut the surroundings at this time. Of course, you can continue to cut it off in the same way as just now, depending on how your hand is more stable. Because I just considered that I wanted to modify its size, I was always cut with a knife, and this step was not needed, so I could cut it directly.
At this time, take out the fillet tool and stuff it in to cut the rounded corners. A small card for the joint paper bag of the tomb robbery note and the overlord coffee table is ready. It is safer if it has thickness, and then a layer of film is attached on both sides without worrying about staining it, and this film can actually be stuffed into it and preserved, like an ordinary small card.
