Zhifeixia UAV operation ten steps qu ben Kunming UAV training Xinjiang foundation

Drone operation ten-step songbook

(1). Prepare the remote control. Put the battery into the remote control → put the L1 and L2 levers in the middle position→ the antenna in the left horizontal position→ install the image transmission display to the remote control→ open the remote control switch, check the power → toggle the fine adjustment switch, check whether to lock the → the up and down left and right directions of the lever, check the joystick feel.

(2). Install the propeller. Mount the propeller on the wing, pay attention to the direction marked by the fixed nut and the arm, and then lock it with a wrench.

(3). Install aircraft batteries. Press the two buttons of the battery 3S at the same time, start the battery, install it to the bottom of the battery compartment, and confirm that the battery is not loose.

（4）． Start the monitor. Press the 3S button on the side of the monitor to debug the shooting screen and confirm the success of the start and frequency conversion.

（5）． Calibrate the compass. Switch the L1 lever from top to bottom more than 5 times→ until the four wing indicators flash at the same time→ place the lever in the middle position→ rotate the fuselage clockwise for more than 4 weeks until the wing indicator becomes solid.

(6). Unlock operation. Check the monitor parameters→ the GPS indicator must be on constantly, the number of satellites must be more than 5 ≧→ the aircraft battery power ≧ 11V→ start the aircraft motor, the left and right joysticks are simultaneously unlocked downwards inward or outward→ confirm whether the motor has abnormal noise and is idle.

（7）． Take-off operation. The operator, facing the direction of the aircraft battery→ slowly push the throttle stick upwards→ confirm whether the aircraft can leave the ground vertically and smoothly→ if the take-off is normal, you can continue to push the throttle stick upwards to complete the work during the take-off process.

(8). Airplane mode operation. Standard mode→ L1-Medium, L2-Medium; Heading Lock Mode→ L1-Medium, L2-1; Interest Surround Mode→ L1-Median, L2-0; Aerial Photography Mode: L1-0, L2-Medium, Automatic Return Mode: L1-1, L2-Medium →When turn on the automatic return mode, you must pay attention to check whether the aircraft is full of power to avoid vertical landing due to power exhaustion.

(9). Shooting mode operation R1 is the camera function selection switch (three-gear switch): camera setting mode: R1-Medium; photographic mode: R1-1: Camera mode: R1-0; R2 is the camera operation switch (reset switch): When the R1 switch is in the R1-1 position, every time R2 is toggled, complete a photo; when R1 is in the R1-0 position, every time R2 is dialed, the camera loops between the start of the camera and the camera stop; when R1 is in the middle position of R1- and R2 is the key to set, For details, please refer to the camera settings.

(10). Safe landing operation. Lower the aircraft to the top of the take-off point→ to ensure a smooth landing, slowly pull down the throttle rocker→ when the aircraft is close to the ground, quickly pull the throttle rocker to the lowest point→ after the aircraft completely lands on the ground, keep the throttle lever above the lowest point 10S, until the propeller stops rotating, that is: lock the motor → take out the aircraft battery, and press the two buttons 3S at the same time, that is, turn off the battery→ take out the remote control battery→ the aircraft landing is completed.

Please choose an open and non-interference flight area to avoid flying under extreme meteorological conditions; check whether the mechanical locking structure is reliable (such as: paddle cap, gimbal link, tripod, battery, etc.) before take-off; the number of satellites found must be more than 5 to take off; pay attention to the power of the aircraft, control the reasonable flight altitude and distance, strictly follow the operating instructions, standardize operation, take off and land smoothly, and ensure flight safety.