But today we are not just planting an LGA1700 radiator for everyone, but a complete set of chassis cooling solutions, which is the GX580H water-cooled version of the chassis from Hangjia and the GX240S Tiger Shark integrated water-cooled radiator.
Hangjia GX580H water-cooled version chassis
The Hangjia GX580H water-cooled version chassis belongs to the GX wide-body game series and is a mainstream high-value chassis for needle gamers. The positioning and price are lower than the GX680 we have previously reviewed, but the Hinge glass side panels, the top 240 water cooling, the back cable management, and the support for 320mm long graphics cards have not fallen behind.
As a mainstream chassis, hangjia GX580H water-cooled version of the product size will be smaller (less than the GX680X), respectively, 380 (long) x210 (width) x485 (high), looking like a more compact chassis, but the installation of atx motherboards is still more positional.
We received a white version, the entire appearance is mainly white, the inside side is a blackened box; of course, if you are black control, then you can also consider the black version. And the most eye-catching is definitely the magnetic design of the hinge glass side panel,
This design not only allows everyone to see the accessories inside, but also practical and easy to remove.
Hangjia GX580H water-cooled version of the chassis maximum support ATX standard specifications of the large motherboard, while downward compatible with MATX and ITX small board; and the maximum length of the graphics card reaches 320mm length, can be compatible with most of the mainstream length specifications of the graphics card; CPU heatsink height limit of 160mm, the same mainstream radiator can still be installed, but it is recommended that everyone is still better to buy an integrated water-cooled radiator.
The depth of space on the inside of the right panel is 28mm, and the traces are quite easy. At the same time, the two SSDs are located on the left side, which is also more convenient to install.
The heat dissipation of the entire chassis is still relatively good, three 120mm or 140mm fans can be installed on the front panel, the top is a 240mm integrated water-cooled radiator mounting position (two 140mm fans can be installed), and the back is a 120mm fan position.
The IO interface of the chassis is located in the chassis, equipped with a switch button, a USB3.0 interface, two USB2.0 interfaces, two 3.5mm audio interfaces, and a restart button.
The bottom of the chassis is the air inlet of the power supply, and the power supply can have independent cooling air channels. The right side is the fixed position of the hard disk cage, the hard disk position can be adjusted according to the length of the power supply, of course, you can also remove the hard disk cage (without the case of 3.5-inch hard disk).
The hard disk cage can be moved to the left to allow the power supply to have more space, when installing the machine, the author is recommended that you first put on the hard disk cage to remove it, and then install the power supply and then install it back into the hard disk cage.
The enclosure can accommodate two 3.5-inch HDDs, one of which is inside the cage and one on top of the cage. The top of the cage can also be replaced with a 2.5-inch hard drive, so that the chassis can be installed with a 3.5-inch hard drive and three 2.5-inch hard drives.
We are evaluating the DIY installed power supply using Hangjia WD650P dual certified platinum power supply (CCC+CQC), due to the design of the non-module line, so the installed cable will look a bit messy.
The front installation effect is still quite OK, of course, the MATX motherboard selected here leaves a lot of heat dissipation space.
Hangjia GX240S tiger shark integrated water-cooled radiator
Hangjia GX240S Tiger Shark integrated water-cooled radiator side is the LGA1700 integrated water-cooled radiator specially optimized for 12th generation Core processors.
The water-cooled head is not large, and the biggest advantage is in terms of silence and memory compatibility.
The water-cooled bottom is designed for pure copper
LGA1700 fastener
It is accompanied by two GX120S Tiger Shark PWM fans
The fan has an RGB design inside, and as opposed to the ARGB interface, it has a variety of RGB lighting effects.
The installation process is not much to say, after all, the installation process of hangjia GX240S tiger shark integrated water cooling radiator is really simple.
Here shows the content compatibility of the Hangjia GX240S Tiger Shark integrated water-cooled radiator, which basically does not occupy the first memory slot and will not appear in the top content.
RGB lighting effect display
When the DIY was installed, we deliberately installed three Hangjia 120mmRGB fans because the chassis did not have fans by default. We all know that Hangjia has also launched a lot of classic and easy-to-use products on the cooling fan, and everyone has time to pay full attention to DIY hardware products such as Hangjia power supply, chassis, CPU heatsink, and cooling fan.
Three fans do exhaust, two fans in front of the suction, so that the negative pressure effect inside the chassis will be achieved, and the heat dissipation effect will be relatively good.
One on the front
The overall effect is still good after installing the hinge glass side panel, and it is indeed a high-value chassis.
Summary: As a mainstream chassis with high value in the GX580H water-cooled version, it has a high space utilization efficiency, which can be stuffed with a standard ATX motherboard, a 320mm length graphics card, a 160mm high radiator, and an overhead 240 integrated water cooling. Compared with the game chassis in the same price segment, this GX580H water-cooled version configuration and duct design is really good, of course, we recommend that you buy three chassis fans at the same time as buying the chassis to enhance the heat dissipation performance in the chassis.