分享興趣，傳播快樂，增長見聞，留下美好！
親愛的您，這裡是LearningYard新學苑。
今天小編為你帶來
暢享聊：SolidWorks學習（17）
歡迎您的通路！
Share interests, spread happiness, increase knowledge, and leave beautiful!
Dear you, this is LearningYard Academy.
Today, the editor brings you
Changxiang Chat:SolidWorks Learning (17)
welcome your visit!
本期我們使用solidworks完成風扇電機座和防滑襯套，首先在前視基準面上進行草圖繪制，畫出如下圖的草圖樣式，然後選擇等距實體，這樣畫出薄壁寬度，接着設定相應的尺寸，完成後就可以選擇旋轉凸台，得到下面的旋轉體。
In this issue, we used SolidWorks to complete the fan motor base and anti slip lining. Firstly, we sketched on the front reference plane, drawing the sketch style as shown in the figure below. Then, we selected equidistant entities to draw the thin-walled width, and set the corresponding dimensions. After completion, we can select the rotating boss to obtain the rotating body below.
然後再端面上草圖繪圓，在使用圓周陣列得到六個圓，使用拉伸切除得到六個圓孔。接着在下圖所示的面上畫出圓形草圖，然後進行圓周陣列得到三個圓形草圖，點選完成草圖，再點選特征，進行拉伸，使所畫圓拉伸到下一平面。
Then sketch a circle on the end face, use a circular array to obtain six circles, and use extrusion to cut off six circular holes. Next, draw a circular sketch on the surface shown in the figure below, then perform a circular array to obtain three circular sketches. Click to complete the sketch, then click on the feature to stretch the drawn circle to the next plane.
完成後，再在剛才的平面上，以剛才繪制的草圖圓圓心為圓心繪制校園，半徑2.5mm，然後同樣使用圓周陣列，使用拉伸切除，切除深度設為8mm，完成後如下圖的模樣。然後進行倒圓角和倒角，最後在對外觀進行調整即可儲存。
After completion, draw the campus on the plane just now with the center of the sketch circle as the center, with a radius of 2.5mm. Then, use the same circular array and stretch to cut, with a cutting depth of 8mm. After completion, it will look like the following image. Then perform rounding and chamfering, and finally adjust the appearance to save.
然後繪制防滑襯套，這個零件非常簡單，首先在前視基準面上畫出兩個圓，大院直徑10mm，小圓直徑我們設定為4mm。然後進行凸台拉伸，拉伸長度為5mm。然後進行倒圓角和倒角，參數都為0.2mm。
Then draw the anti slip lining. This part is very simple. First, draw two circles on the front reference plane, with a diameter of 10mm for the large courtyard and 4mm for the small circle. Then perform protrusion stretching, with a stretching length of 5mm. Then perform rounding and chamfering, with parameters of 0.2mm.
今天的分享就到這裡了。
如果您對今天的文章有獨特的想法，
歡迎給我們留言，
讓我們相約明天，
祝您今天過得開心快樂！
That's it for today's sharing.
If you have a unique idea about today’s article,
Welcome to leave us a message,
Let us meet tomorrow,
I wish you a nice day today!
本文由learningyard新學苑原創，如有侵權，請聯系我們。
部分内容參考于bilibili，百度
翻譯來源：通義千問
文字&排版｜calm
稽核｜歪歪