Teach everyone how to use this Type 60 delay camera.
First of all, there is a 60 delay camera. The first step is to connect the power supply, here is a power cord, triangle, plug the power triangle plug into the wire board. The second step is to insert the trachea well, which is a trachea with the outside eight, and insert it from this position. There is a barometer here that will have a pressure display on it, and here it will be adjusted to two kilograms, that is, zero point two runs. When you see this pointer, you must point to the position of two kilograms.
When the power supply is ready, you can now turn on the power switch. Now as soon as the power switch is turned on, do you find that there are three lights on here, which are first of all short of water, and there is a shortage of salt water, and the pressure barrel is short of water. The three lights are lit to indicate a lack of water in these three places.
So what to do? Now just like these three places to replenish water, the laboratory is short of water, here first open the lid, this whole empty represents a laboratory space, the laboratory water is directly poured from here, the water added is clear water. Pay attention to the lack of water lamps, when the water level reaches the surface, the lack of water lights will be extinguished. See if you find a lamp flashing now, and the water is slowly adding.
Now that the lights have been turned off, it means that all the water levels are enough and there is no need to add more water. Water added is clean water, must pay attention to the time is now to add clear salt water, salt water is added from here, the configuration is usually used in the car is five percent concentration of sodium chloride solution, the configuration is a bottle, here is a bottle of sodium chloride, is five hundred grams, five percent solubility. How is it formulated? A bottle of salt to 9.5 liters of water, take this measuring cup here is a buckle is five liters, the 9.5 liters have been measuring a five liters, and then measure a 4.5 liter, that is, a long 9.5 liters, you need to consume a bottle of salt, this 500 grams of sodium chloride, mix it evenly to get a water, the solution is a sodium chloride solution, that is, a concentration of five percent concentration sodium chloride solution.
The configured sodium chloride is added from this. Here at the intersection of the four units, now it is replaced by clean water, and after adding it, it is actually already flowing inside the machine, and it will slowly flow into this space, here is a plate and five cages and a greenery is not, in fact, it is left here, and then now it is directly poured with clean water.
Have you noticed that now, indeed the lights have been extinguished, indicating that the water is already available, and it is enough to do experiments. However, test water is usually done, and in the process of doing it, if the time is relatively long, the amount of salt water needed will be more, and you can fill it up. There is still one pressure hole left in the area, which is still drying.
Add water here to add water from a pressure barrel water hole here, be sure to add pure water, must remember that before adding water, there is a red ball valve below with a gray leak, this red ball valve must be opened before opening, so it is closed.
・Be sure to open it before adding it now, and then slowly add it from it after opening. Pure water here must pay attention, must add pure water, at this time you can move slower, don't clamp too quickly, to prevent the water from overflowing. Now you can observe the water lamp, whose water level has reached the designation, because this water lamp will also
Now that the water shortage lamp has been extinguished, it means that the water is located in one. You can now turn off the red ball valve after replenishing water. There is also a place to replenish water, the hive should also be sealed with clean water, and water should also be added here to seal the lid to prevent the smoke from seeping in. By the way, after the water in these four places is replenished, you can operate below.
Turn on the power operation switch, after the operation switch is turned on, you will find that the two temperature control meters will have a temperature display, the temperature here represents the laboratory temperature represents a temperature in a laboratory just now, the temperature of this pressure barrel is inside, and there is a set temperature in the insulation barrel.
Then open and open, before leaving the factory, this temperature has been debugged, here is thirty-five degrees forty-seven degrees, this is also done later, the test process does not need to be fixed.
Now go to the back is to put the product for testing, where to put the product? There are two kinds of payment racks, one is micro, some products with some large parts can be placed on the micro payment shelf. There are four miniature payracks.
After the bracket is arranged, you can put a special product that you usually want to make on it. There is also an Alipay element here, there are six strips. How is this product arranged? According to the user's actual needs to arrange, after the product is placed correctly, the lid is closed, and the spray switch can be turned on.
Open the spray to see, now there is no fog spraying out, indicating that the air pressure inside does not show no barometer, and does not show that there is no air pressure inside. The spray pressure inside is then adjusted by means of a pressure regulator.
The air pressure is not displayed yet, so adjust the spray pressure inside by adjusting the front pressure regulator. First of all, before adjusting the pressure regulating switch to pull out, and then rotate clockwise like this, it is found that there is no current pointer is slowly walking, when twisted here the pointer will rise a little, the air pressure is adjusted to one kilogram. Now that the air pressure has reached one kilogram, it freezes at one kilogram at this time, and then press the rotary button. After the air pressure has been debugged, in the position of the car, the air pressure should not be changed, at this time to see that no, there is fog sprayed out here.
This is the spray tower, from which the whole fog is sprayed, and the position of the spray tower is now the best position. During the process of use, the height of the spray tower is adjusted according to the delay of collecting one of its own cylinders. If the amount of spray collected is greater than one to two milliliters per hour, the position of the spray tower can be lowered, if it is less than one milliliter, the position of the spray tower can be adjusted up a little higher every hour, and the spray tower can be adjusted up and down here.
