【rk3288w】【android9.0】 MIPI屏幕配置指南

Rockchip显示操作---MIPI屏幕

• • • uboot驱动
    • • 接口说明
    • kernel 驱动
    • 常用的debug手段

uboot驱动

/*核心驱动*/
drivers/video/drm/rockchip_display.c
drivers/video/drm/rockchip_panel.c
/*MIPI-DSI*/
drivers/video/drm/rockchip_mipi_dsi.c
drivers/video/drm/rockchip-dw-mipi-dsi.c
/*Panel*/
drivers/video/drm/rockchip_dsi_panel.c
drivers/video/drm/panel_simple.c
           

接口说明

1. void rockchip_show_logo(void)

   显示uboot logo和kernel logo

2. void rockchip_show_bmp(const char *bmp)

   显示指定的bmp图片，目前只要用于uboot logo充电的显示

3. rockchip_display_fixup(void *blob)

   将uboot中确定的一些变量通过dtb文件传递给内核，包括kernel logo的大小，地址，格式，输出扫描时序以及过扫描的配置等信息

kernel 驱动

driver/gpu/drm/panel/panel_simple.c
           

1. 驱动一般不需要更改，但需注意函数

   static int panel_simple_prepare(struct drm_panel *panel)

   需要与屏幕规格书中保持一致
2. dts配置如下参考

&dsi0 {
	status = "okay";
	rockchip,lane-rate = <750>;

	panel: panel {
		compatible = "simple-panel-dsi";
		reg = <0>;
		backlight = <&backlight>;
		enable-gpios = <&gpio7 3 GPIO_ACTIVE_HIGH>;
		reset-gpios = <&gpio7 4 GPIO_ACTIVE_LOW>;
		dsi,flags = <(MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST | MIPI_DSI_MODE_LPM)>;
		dsi,format = <MIPI_DSI_FMT_RGB888>;
		dsi,lanes = <4>;
		reset-delay-ms = <50>;
		init-delay-ms = <120>;
		enable-delay-ms = <50>;
		prepare-delay-ms = <50>;
		status = "okay";

		panel-init-sequence = [
			29 00 04 FF 98 81 03
			13 00 02 cb 63
			13 00 02 cc 18
			13 00 02 cd 16
			13 00 02 ce 4d
			13 00 02 cf 1f
			13 00 02 d0 2a
			13 00 02 d1 4f
			13 00 02 d2 5f
			13 00 02 d3 39
			29 00 04 ff 98 81 00
			05 78 01 11
			05 14 01 29
		];

		panel-exit-sequence = [
			05 14 01 28
			05 78 01 10
		];

		disp_timings: display-timings {
			native-mode = <&timing0>;

			timing0: timing0 {
				clock-frequency = <68800000>;
				hactive = <800>;
				vactive = <1280>;
				hback-porch = <20>;
				hfront-porch = <20>;
				vback-porch = <20>;
				vfront-porch = <30>;
				hsync-len = <20>;
				vsync-len = <4>;
				hsync-active = <0>;
				vsync-active = <0>;
				de-active = <0>;
				pixelclk-active = <0>;
			};
		};
	};
};

&route_dsi0 {
	status = "okay";
};

&dsi0_in_vopl {
	status = "okay";
};

&dsi0_in_vopb {
	status = "disabled";
};
           

panel-init-sequence

中的

29

,

13

,

05

表示包名，一般为

39

,

15

,

05

，具体情况需要看屏幕规格书

常用的debug手段

cat d/dri/0/summary

查看vop的打开在状态以及屏幕接口

cat /sys/kernel/debug/gpio

查看gpio状态，确认gpio配置是否正常

新人报到，多多关照！