grub:
115200 ramdisk_size=60000 earlycon=ppl011,mmio32,0x28001000 bonding.miimon=100 bonding.mode=active-backup libata.dma=5 quiet root=/dev/ram0 rw pci=noaer pcie_aspm=off net.ifnames=0
initrd /initrd.gz
bootload:
bootargs root=/dev/mtdblock2 console=ttySAC0 init=/linuxrc
- root:指定根文件系统的位置,比如:root=/dev/mtdblock3 , mtdblock3 代表mtdparts的第4分区 (第一个分区为mtdblock0) 如果指定 root=/dev/nfs,还需要指定nfsroot=serverip:nfs_dir
- console:设置控制台参数,比如:console=ttySAC0,115200 , 使用串口0作为控制台,波特率为115200 。串口设备要根据实际的设备名称来设置。
- rootfstype:指定根文件系统的类型,这个选项需要跟root一起配合使用,一般如果根文件系统是ext2的话,有没有这个选项是无所谓的,但是如果是jffs2,squashfs等文件系统的话,就需要rootfstype指明文件系统的类型,不然会无法挂载根分区。
- ramdisk_size:指定创建的ramdisk的大小,ramdisk是将内存中的一块区域作为物理磁盘使用的一种技术
- init:指定内核启动后第一个执行的脚本,比如:init=/linuxrc
- initrd:指定ramdisk在内存中的位置和大小
有个疑问grub or uboot 解析完参数后传给内核! 内核怎样解析参数。
以quite net.ifname=0 log_level为例:
init/main.c中:
static int __init quiet_kernel(char *str)
{
console_loglevel = CONSOLE_LOGLEVEL_QUIET;
return 0;
}
early_param("quiet", quiet_kernel);
static int __init loglevel(char *str)
{
int newlevel;
/*
* Only update loglevel value when a correct setting was passed,to prevent blind crashes (when loglevel being set to 0) thatare quite hard to debug
*/
if (get_option(&str, &newlevel)) {
console_loglevel = newlevel;
return 0;
}
return -EINVAL;
}
early_param("loglevel", loglevel);
当内核 cmdline 中设定了 quiet 参数后,quiet_kernel 函数会被调用,这个函数会将 console_loglevel 设定为CONSOLE_LOGLEVEL_QUIET=4
我们知道内核是依次执行各个section代码段代码。来看early_param的宏定义展开。
/*
* Only for really core code. See moduleparam.h for the normal way.
*
* Force the alignment so the compiler doesn't space elements of the
* obs_kernel_param "array" too far apart in .init.setup.
*/
#define __setup_param(str, unique_id, fn, early) \
static const char __setup_str_##unique_id[] __initconst \
__aligned(1) = str; \
static struct obs_kernel_param __setup_##unique_id \
__used __section(.init.setup) \
__attribute__((aligned((sizeof(long))))) \
= { __setup_str_##unique_id, fn, early }
#define __setup(str, fn) \
__setup_param(str, fn, fn, 0)
/*
* NOTE: fn is as per module_param, not __setup!
* Emits warning if fn returns non-zero.
*/
#define early_param(str, fn) \
__setup_param(str, fn, fn, 1)
扩展后结果为:
static const char __setup_str_loglevel[] __initconst __aligned(1) = "loglevel";
struct obs_kernel_param _setup_loglevel
__used __section(.init.setup)
__attribute__((aligned((sizeof(long)))))
= {
.str = "__setup_str_loglevel",
.setup_func =loglevel,
.early = 1,
};
/* These are for everybody (although not all archs will actually
discard it in modules) */
#define __init __section(.init.text) __cold notrace
#define __initdata __section(.init.data)
#define __initconst __constsection(.init.rodata)
#define __exitdata __section(.exit.data)
#define
其含义为:
- const char __setup_str_loglevel[]其值为 “loglevel”,存放在.init.rodata section中并以 1 字节为单位对齐
- struct obs_kernel_param _setup_loglevel 此结构体以 sizeof(long) 字节对齐并存放到.init_setup section 中
内核启动的时候其会调用如下函数:
start_kernel
setup_arch
parse_early_param
parse_early_options
parse_args
parse_one
do_early_param
/* Arch code calls this early on, or if not, just before other parsing. */
void __init parse_early_param(void)
{
static int done __initdata;
static char tmp_cmdline[COMMAND_LINE_SIZE] __initdata;
if (done)
return;
/* All fall through to do_early_param. */
strlcpy(tmp_cmdline, boot_command_line, COMMAND_LINE_SIZE);
parse_early_options(tmp_cmdline);
done = 1;
}
/* Check for early params. */
static int __init do_early_param(char *param, char *val,
const char *unused, void *arg)
{
const struct obs_kernel_param *p;
for (p = __setup_start; p < __setup_end; p++) {
if ((p->early && parameq(param, p->str)) ||
(strcmp(param, "console") == 0 &&
strcmp(p->str, "earlycon") == 0)
) {
if (p->setup_func(val) != 0)
pr_warn("Malformed early option '%s'\n", param);
}
}
/* We accept everything at this stage. */
return 0;
}
#define INIT_SETUP(initsetup_align) \
. = ALIGN(initsetup_align); \
VMLINUX_SYMBOL(__setup_start) = .; \
*(.init.setup) \
VMLINUX_SYMBOL(__setup_end) = .;
do_early_params 函数的第一个参数是上层传入的 cmd 的唯一标识,然后 do_early_params 函数遍历 __setup_start以及 __setup_end代码段区域内遍历每一个 cmd实例--->obs_kernel_param,匹配到了则调用相应的 setup_func hook函数!!
关于section,目前内核连接各个模块等都是通过section来存放链接。
以下为内核启动参数参考:
Console Options | |||
参数 | 说明 | 选项 | 内核配置/文件 |
console=Options | 用于说明输出设备 | ttyn 终端 ttySn[,options], ttyUSB0[,options] 串口uart,io,addr[,options],uart,mmio,addr[,options]&<60; | |
netconsole=[src-port]@[src-ip]/[dev],[target-port]@target-ip/[targetmac-address] | |||
debug | Enable kernel debugging. | 启动时将所有的调试信息都输出到控制台 | |
quiet | Disable all log messages. | 相当于loglevel=KERN_WARNING | |
earlyprintk=[vga|serial][,ttySn[,baudrate]][,keep] | 打印传统的控制台初始化前的信息,主要是硬件相关的信息 | ||
loglevel=level | 设置默认的控制台记录级别 | 所有的较高级别的信息将被打印(0-7) | /proc/sys/kernel/printk |
log_buf_len=n[KMG] | 设置内核记录缓冲区大小 | 为2的冥 | CONFIG_LOG_BUF_SHIFT |
initcall_debug | 调试系统初始化函数 | 跟踪系统启动时用到的所有的函数 | |
kstack=n | Oops栈的多少个字被输出 | n为整数 | |
time | 在记录信息前面显示时间 | ||
Interrupt Options(Advanced Programmable Interrupt Controller APIC) | |||
apic=[quiet|verbose|debug] | 改变ACPI子系统启动时的记录级别 | 默认为quite | |
noapic | 不用任何IOAPICs | ||
lapic | 使本地ACPI有效 | 即使BOIS使得它无效,也要让它有效 | |
nolapic | 不使用ACPI | ||
noirqbalance | 使内核内建的Irq平衡逻辑无效 | ||
irqfixup | 基本的中断问题修复 | 当一个中断没有被处理,搜索所有的中断处理看看能不能用 | |
irqpoll | 扩展的中断问题修复 | 在每一个时钟中断,检查每一个中断处理 | |
noirqdebug | 禁止未处理的中断自动探测 | 默认情况下,内核试着探测并且禁止未处理的中断源,以免引起未知的问题,这个选项禁止该功能。 | |
Memory Options | |||
highmem=n | 说明高内存区域的大小 | 强制高端内存有大小为n的精确的内存区域,不管系统有没有高端内存,也可以用于减少大内存系统中的高端内存大小 | |
hugepages=n | 设置hugetlb页的数量 | ||
ihash_entries=n | 设置Inode哈希表的大小 | 用于覆盖内核的默认值 | |
max_addr=n | 设置内存的最大地址 | 内核将忽略在该地址以上的物理内存 | |
mem=n[KMG] | 设置内存使用的内存数 | 当使用memmap选项时,能避免物理地址空间的冲突。如果不用memmap选项,可能引起PCI设备被放到未用的RAM空间。 | |
mem=nopentium | 内核禁用大页(4M) | ||
memmap=exactmap | 使用特定的内存映像 | ||
memmap=n[KMG]@start[KMG] | 强制内核使用特定的内存区域 | n,是表内存区域的大小,start指内存区域的开始位位置 | |
noexec=[on|off] | 禁/启用内核将一个内存区域映像为不可执行内存的的功能。默认为on. | ||
reserve=n[KMG] | 强制内核忽略IO内存区域 | 预留IO内存区域 | |
vmalloc=n[KMG] | 强制vmalloc有的个特定的大小 | 可用于增加vmalloc区域的最小值,也可以用于减少vmalloc的大小,增加更多的空间用于直接映射内核RAM | |
norandmaps | 不用地址空间随机化 | 默认内核随机化程序启动的地址,该选项禁用该功能 | /proc/sys/kernel/randomize_va_space写0相当 |
vdso=[0|1] | 禁/启用vdso映像 | (Virtual Dynamic Shared Object),默认为启用 | |
Suspend Options | |||
resume=suspend_device | 说明休眠文件的分区设备 | ||
noresume | 禁用休眠功能 | ||
Ramdisk Options | |||
initrd=filename | initrd Ramdisk的位置 | 说明内核启动时要用到的Ramdisk的位置 | |
load_ramdisk=n | 从软盘加载Ramdisk | n=1,则从软盘加载ramdisk | |
noinitrd | 不用任何Initrd,即使参数时面指定了 | ||
prompt_ramdisk=1 | 在从软驱中读取ramdisk之前提示用户 | ||
ramdisk_blocksize=n | ramdisk的块尺寸 | ||
ramdisk_size=n | 说明ramdisk的大小 | ||
Root Disk Options | |||
ro | 启动时以只读方式挂载根文件系统 | 如果在它之前有rw的选项,ro将会取代它 | |
root=device | 说明系统启动的根文件系统 | nnnn 十六的制备号(以内核可识别的方式表示major和minor)/dev/nfs/dev/<diskname>/dev/<diskname><decimal>/dev/<diskname>p<decimal>(要求diskname以数字结尾) | |
rootdelay=n | 挂载文件系统前的延迟 | 主要是当根文件系统在USB or FireWire设备上 | |
rootflags=options | 根文件系统挂载选项 | ||
rootfstype=type | 根文件系统的类型 | 例如:rootfstype=ext3 | |
rw | 启动时以读写方式挂载根文件系统 | ||
Init Options | |||
init=filename | 在Init时,应该执行的程序 | 默认为/sbin/Init | |
rdinit=full_path_name | 从ramdisk中运行Init进行 | 指定的文件必须是在ramdisk而不是在root文件系统中 | |
S | 运行Init在单用户模式中 | ||
Network Options | |||
netdev=[irq],[io],[mem_start],[mem_end],[name] | 设备各咱网络参数 | ||
thash_entries | 设置TCP连接哈希表的最大数目 | ||
Network File System Options | |||
lockd.nlm_grace_period=n | 设备恰当的锁管理周期 | 以秒为单位 | |
lockd.nlm_tcpport=port | 为NFS锁管理者设置端口(TCP) | ||
lockd.nlm_timeout=n | NFS锁管理者超时 | 默认为十秒 | |
lockd.nlm_udpport=port | 为NFS锁管理者设置端口(UDP) | ||
nfsroot=[server-ip:]root-dir[,nfs-options] | 为无盘系统,说明NFS根文件系统,如果参数没有设置默认为/tftpboot/client_ip_address | ||
nfs.callback_tcpport=port | 为回调通道设置NFSv4&<60;TCP端口 | ||
Hardware-Specific Options | |||
nousb | 没有USB设备 | ||
lp=[0|port[,port…]|reset|auto] | 设置并行端口和其模式 | lp=auto内核将检查所有端口,看有没有IEEE&<60;1284兼容的打印机 | |
parport=[setting[,setting…] | 说明并行端口参数 | ||
parport_init_mode=[spp|ps2|epp|ecp|ecpepp] | 并行端口初始化模式 | ||
nr_uarts=n | 最大的UART被注册的数目 | ||
panic=n | 系统panic后重启最大等时间 | 默认为0,系统将不重新启动,仅仅挂起 | |
pause_on_oops=n | 告诉内核,当第一个Oops出现后,挂起所有的CPU,n秒,以便记录下现场 | ||
combined_mode=[combined|ide|libata] | 说明IDE驱动 |