I found out today that it turns out that threading the needle and lead is so simple, only need to use a bottle cap, no matter how small the pinhole, no matter how thick the thread, it only takes one second to easily pass through, follow the video to take a look, hello everyone, I am Peng Peng.
Although the times are getting more and more progressive, but from ancient times to the present, sewing and mending are indispensable in our family, and we can't break a little thread, so we can take it to the street and spend a few dollars to let others repair it, so we now have a lot of families, or will use needles and threads to sew and mend themselves, but ah, threading has become a big trouble for us.
It's not a problem for us young people, but for middle-aged and elderly people or friends with presbyopia, it will cause a lot of trouble, how to wear this needle and thread can't be worn, if you don't do this kind of fine work all the time, then people's hearts will be very irritable!
Today I will share with you a few tips for threading the needle, which can be easily passed through in one second, and follow the video to understand it!
Technique one, we prepare a scotch tape like this, scotch tape is available in every household, we tear it open, and then cut it with scissors, such a small piece, and then wrap the thread we need to thread in the scotch glue.
Because the transparent glue has a certain hardness, and it is particularly thin, and our thread is relatively soft, so it will not pass through the pinhole, we wrap the thread in the transparent glue, and then trim it with scissors again, cut it into a sharp corner, like this, and then use this sharp corner to insert it from the pinhole in this way.
Because the angle is relatively hard, it can be easily passed through, after passing through, we pull the thread at one end, take out the thread, and then tear the transparent glue to it, of course, I personally think that this method is more troublesome than the latter method, because after sticking the transparent glue, we have to disassemble it, in fact, it also wastes a lot of time, although it is easier to thread this way, of course, it is much faster than directly using the thread to wear.
Technique two, we find out the thread that needs to be threaded, we put it in the palm of the hand, try to put a thread in the palm of the hand, and then find out the needle that needs to be threaded, align the pinhole with the thread, and then rub it so hard, of course, like this the thread is not placed, we use the finger seam to clamp it, rub it again, so that the heat is generated by friction, then the thread will be absorbed by the pinhole, so as to achieve the effect of passing the needle and thread, this method is also called friction threading, I don't know if you have tried this method.
Technique three, find a toothbrush, the bristles of the toothbrush are not only particularly thin, but also soft and hard, we put the thread that needs to be worn on the toothbrush, and then gently press down with the pinhole alignment line, so that the thread will be squeezed out by the bristles of the toothbrush, so as to pass our thread through the pinhole, this method can also easily pass the thread through the pinhole, I don't know friends, have you tried this method.
Technique four, we prepare two brooms or brushes on the bristles, this bristles are not only very fine, but also no burrs, hardness is moderate, we only need to find a mineral water bottle cap, or drink cap, or beer bottle cap can be, if you really can't find it, you can replace it with a coin;
Then we will fold the bristles in half like this, fold the place in half, pinch it hard, pinch a dead corner, pinch it into such a pointed shape, pinch it on the bottle cap, and then we find a piece of transparent glue, and firmly stick the folded brush to the bottle cap, so that we have done a needle thread, so how do we use it?
Don't go away, let's go down, we just need to thread the needle, no matter how small the needle hole is, this kind of brush has a certain hardness, and there is no burr, so we can pass it through the pinhole, you can see that the pinhole is very small, and it can be passed through very easily;
After wearing it, we put the thread through this hole to it, such a big hole I believe that I can pass through it with my eyes closed, after wearing it, we take the needle off the lid like this, in the process of removal, the thread will go along the sewing device we made and pass through, no matter how thick the thread is, how thin the pinhole is, you can easily thread it through!
Of course, like this thicker needle, it will be more convenient to wear, let's try it, you can easily pass it through the pinhole, and then use the same method, put our thread through this hole to it, and then fold the thread, take off the needle, naturally, the thread will flow through.
How's it going, friends? This method is not bad, I don't know these methods of threading the needle, which one do you prefer, welcome to leave a message below the video, if you have more tips for threading the needle, just share it, okay, today's video is shared here, we'll see you in the next video, bye-bye. #夏日生活打卡季#