1. Functional selling points:
(1) Function:
1. The program of vacuuming first and then mopping the floor is set, which integrates the functions of strong suction, sterilization, self-cleaning, and drying;
2. One is equivalent to a broom & dustpan + rag + steam mop + vacuum cleaner + sweeping robot + floor cleaning liquid;
(2) Clean technology
1. 13,000 rpm roller brush drive motor, large suction power reaches 10,000pa, and the sewage recovery rate is 99% into the sewage tank.
2. Ground quick-drying technology, powerful fan combined with independent air duct design, the strong wind is aggregated in the range of the mopping head, and the ground is quickly dried while mopping.
3. High-temperature wireless steam technology, through the design of 600W high-power labyrinth boiler, 110°C high temperature and high purity steam are generated to achieve the effect of dissolving stubborn stains;
(3) Sterilization and drying technology
1. Sterilization: self-made sterilization liquid technology with electrolyzed water technology; high-temperature steam technology; The active oxygen water generator prepared by the titanium-platinum alloy device prepares tap water into active oxygen technology, which can achieve a sterilization rate of 99.99%;
2. Drying: self-cleaning + drying without roller cloth roller brush;
(4) Intelligent design
1. Choose the tile mode and floor mode by yourself, and intelligently plan the path;
2. The double roller brush has a front and rear double power assist system, and the front and rear active traction is effortless;
3. The LED strip light can illuminate the ground in front of it when it is running.
4. You can stand by yourself anytime and anywhere, without relying on the base.
5. Three-in-one base: charging, storage, self-cleaning, every time the base is put back after cleaning, the machine will automatically dry the roller brush centrifugal air drying and cleaning the pipe.
2. The following key factors should be considered in the purchase:
(1) The brushless motor is preferred, which drives the motor at a high speed and realizes the rapid friction of the roller brush against the ground;
(2) The double roller brush has a front and rear double power system, which is more labor-saving than the single roller brush: no roller brush - no need to clean the roller cloth, and the self-cleaning function is better;
(3) High sewage recovery rate with high suction, such as more than 10000Pa, the cleaning effect is better;
(4) The base should have a hot air drying function, which can dry the moisture of the roller brush to avoid mildew and odor;
(5) If there are replaceable parts, they can be converted into vacuum cleaners to solve the cleaning problem of sofas, bed bottoms and corners.
3. Introduction to intelligent water exchange:
(1) Working principle: the water pipe is connected to the faucet to replace the clean water tank; The sewage pipe is connected to the sewage outlet, replacing the sewage tank; The principle of the machine washing the mop is similar to that of the washing machine, the water pipe enters the water supply module, the water is sprayed from the water pipe to the mop for cleaning, and the sewage is discharged along the water pipe into the water supply module; There is no need to connect or change water, and the function of regular automatic cleaning is realized;
(2) Intelligent water exchange module design: sewage tank filter anti-clogging, intelligent water exchange device and base station chip transmission, intelligent valve control to fill water on demand, abnormal water leakage alarm;
(3) Intelligent water exchange module and installation accessories
Fourth, the installation of intelligent water exchange base station:
(1) Choose a flat, dry and well-ventilated place for installation:
1. Leave enough space of 1 meter in front of the base station, which will not affect the robot entering and exiting the base station;
2. The height of the room steps at the base station location shall not exceed 2 cm;
(2) Confirm the location of the installation, power supply, water source and drainage drain;
1. If the intelligent water change installation cannot be satisfied, it is recommended to replace the ordinary water tank version;
2. If you need to purchase materials, please confirm the material budget, or the user prepares it by himself;
3. Try not to punch holes, or make small holes, and the punching height is within 20CM;
(3) It cannot be placed on the balcony to prevent it from sun and rain;
(4) Commissioning after installation: carry out one or two base station self-cleaning functions, use paper towels to check whether there is water leakage in each water pipe transfer interface, and check if there is water leakage according to the following methods:
1. The water pipe is not plugged in properly, and it cannot be pulled out under normal circumstances;
2. The water pipe is not cut flat, the raw material belt is not wrapped or not wrapped enough for 15 turns; Waterproof soft rubber no pad; The plumbing nut is not tightened;
3. The water pipe on the back of the base station is not tightened or over-screwed;
(5) Installation examples:
5. Debugging of common problems of intelligent water exchange base station:
(1) Failure of distribution network:
1. Consult the manual and turn off the robot to power off:
2. Base station reset: settings (long press the leftmost button) → general (switch to the third) → reset (switch to the fourth);
3. The robot is turned on and the network is re-distributed;
(2) The robot cannot be searched by the station:
Restart the base station and the robot, disconnect the power of the base station, and turn off the robot; After the power is off for 10s, connect the base station power supply first, then turn on the robot, and wait for rematching.
(3) Unable to self-clean
1. The base station does not respond to self-cleaning, and it will not be used for water; The base station interface does not respond, but it will automatically pump water and cannot enter the drainage interface
2. Elimination: The base station and the robot are operated directly before they are connected, and the water supply and water supply modules are not covered;
3. The operation process after the exclusion: restart the base station after power failure, if you need to reconnect the robot, wait for the connection before operating.
(4) Abnormal hydration:
1. Open the faucet and water valve, and check that the connector wire connecting the solenoid valve is loose;
2. Open the lid of the water tank and add about 500ml of water to the water tank. Take out the sewage tank filter to see if there is a lot of water, if not, it is normal; If there is water in the tank to the float, use a towel to suck some out.
3. Put back the strainer screen of the sewage tank, cover it back and close the lid tightly; After power-off for 10s, plug in the power cord of the base station, turn on the robot, wait for the base station to connect to the robot, carry out the self-cleaning of the base station, and only open the water tank cover after the water is pumped each time, check whether the water tank is replenished normally, and remove the sewage tank filter screen at the same time to check whether the sewage has been discharged.
4. After the inspection, remember to cover and close the lid of the water tank. Note: During the pumping process, the lid of the water tank must not be opened, and it must be closed tightly!
5. If the above methods cannot solve the problem, try not to install the solenoid valve, and then do the shutdown and restart detection, and then install a new solenoid valve after the normal water supply.
(5) Abnormal mop washing:
1. There may be: washing the mop does not produce water, or washing the mop all the time and cannot be stopped;
2. Solution:
(1) Turn off the base station first, and then turn off the robot; The base station is restarted and the robot is turned on again; Start the mopping task to see if it's OK;
(2) If it is still abnormal, the base station will be reset and the robot will be shut down; After the base station reset is completed, the robot will be powered on, wait for the connection, and start the mopping task again;
END!