Recently in the concentrated spray painting transformation of all of Xia Ya's cars, first pictured above:
Okay, let's start drying up later:
- Spraying tools: two portable spray pumps + County Marks pen airbrush
Tips: The spray pump uses high-grade spraying, if the turtle pump is used, the air pressure should not be adjusted too large, otherwise it will blow away the paint surface of the surface. When using the airbrush, be sure to constantly rotate the position of the marker tip to find the best atomization angle.
- Marker selection: This time the metallic red uses the County's marker, metallic red and super metallic red; the black part chooses a paint pen with a high cost performance
tips：
a. The super red and ordinary metallic red of the Kenshi marker can be mixed with each other! This has greatly improved the lack of marks in the county, and this time the slightly lighter red is the result of a mixture of two reds.
On the left is Super Red, and on the right is Ordinary Metallic Red, in the middle is a mixture of the two colors
b. The direction in which the county marker pen is opened is the opposite direction of rotation with the general opening of the bottle cap, this trick must be remembered, otherwise it will never be opened, and the more it is tightened.
The clerk's pen can only be opened by twisting clockwise
c. This time the effect is more amazing is the paint pen, I use this three dollars a cross-ocean, this pen is relatively thick, to be poured into the air traffic control marker, in order to clip on the airbrush to use. The advantage of this lacquer is that the Genjunshi marker pen also uses alcohol as a solvent, is completely non-toxic, has a small odor, and the colors can be mixed and harmonized with each other. However, when spraying directly, the pigment is thicker, and the effect of spraying is not ideal... At this time, the point is that there is a very good trick is to add a small amount of 75% alcohol solvent, and the atomization effect when spraying again after shaking is very amazing, and the matte texture can be directly achieved. The masking effect of the paint pen I use is also very good, and there is no need to spray water in advance to replenish the soil to unify the base color
d. This time also used electroplating color, respectively copper gold and silver, this electroplating pen spray out can have a good mirror effect, but after spraying varnish its plating effect disappeared, into a general metallic color, will be a bit of frosty texture
The electroplated marker used this time
e. This time the skeleton spray uses the iron color of the gun gun of the gun, this color is also very useful, stronger than the super metallic red adhesion, super metallic red is really very squeamish... Later, when playing pose, I will rub off a little paint...
f. There is also the problem of the consumption of paint used in markers, this time the spraying of the mg skeleton basically consumes most of the iron color of the gun, and the metal super red basically consumes a whole one.
- About the masking: This time the miscellaneous masking tape is used... Blood lessons, cover belt must choose Tamiya or Kamoi.
tips: Miscellaneous card covering tape will remain on the paint surface, and will inexplicably dissolve part of the paint surface, resulting in repeated paint washing, which greatly affects the amount of consumables and physical and mental health... Normally speaking, the covering belt of Tamiya and Yajing should not overturn, but this time I still got a little tip, if there will be residual glue left on the paint surface when the covering belt is removed, you can repeatedly use the new covering tape to glue the previous residual glue...
- About the protective paint: This time, the Tamiya varnish spray tank is used
Tips: a. This time basically used up a whole can of varnish. The main reason is to protect the paint surface of the marker spray, and there must be a layer of varnish protection before covering the spray and seepage lines. However, too much varnish will make the marker red paint darker and biased towards warm red. Even if you spray more protection, the red metallic paint surface will have transparent red varnish floating on the protective paint... The reason is because the red metallic paint is made of a mixture of metallic silver and transparent varnish, and when the varnish is sprayed, the red varnish will break away from the original silver metallic paint surface and float to the protective varnish... Anyway, wear gloves when playing...
b. In order to save the amount of paint this time, most of the protective paint is sprayed after the overall assembly is assembled. Generally speaking, the arms and limbs of the model are placed as far apart as possible to avoid dead ends. At this time, it must be noted that the range of sliding through the model arm when the horizontal expansion of the spray must be increased, otherwise there will be a situation where the end of the arm is stuck to a relatively large non-atomized droplet...
5. About the infiltration line: This time the Tiangong enamel infiltration liquid is adopted
tips: Enamel Dafa should normally have a good performance on the surface of the marker paint, but the super color of the marker will be dissolved by the enamel paint... Therefore, be sure to spray varnish before infiltrating the line
Finally, it is also necessary to do a good job of protection, even the mark airbrush must be operated with a gas mask. When spraying varnish, you still need an outdoor ventilation environment, or it is best to make a spray box.
To make your own spray box, be sure to choose a fume fan with large pumping power
The above is the experience sharing, I hope that everyone can enjoy the process of turning plastic into handicrafts with simple equipment.