RationalDMIS 2020 功能之程式停止指令

提示：

程式設計時，使用該指令可以減少斷點和提示語句的輸入，友善測量，防止碰撞！作用相當于DMIS标準中的PASUE功能。。。

RationalDMIS程式暫停指令：​

​RESUME/STOP​

​

$$*/
MODE/PROG,MAN
F(CIR1)=FEAT/CIRCLE,INNER,CART,57.1500,81.2800,-3.0000,0.0000,0.0000,1.0000, 50.8000
$$ Measurement points are created through nominal points
MEAS/CIRCLE, F(CIR1), 4
  PTMEAS/CART, 82.0498,  76.2638, -3.0000, -0.9803,  0.1975, 0.0000
  GOTO/CART,   79.1302,  85.5963, -3.0000
  GOTO/CART,   75.8053,  93.6792, -3.0000
  GOTO/CART,   69.6403,  99.8744, -3.0000
  PTMEAS/CART, 62.1662, 106.1798, -3.0000, -0.1975, -0.9803, 0.0000
  GOTO/CART,   52.8337, 103.2602, -3.0000
  GOTO/CART,   44.7508,  99.9353, -3.0000
  GOTO/CART,   38.5556,  93.7703, -3.0000
  PTMEAS/CART, 32.2502,  86.2962, -3.0000,  0.9803, -0.1975, 0.0000
  GOTO/CART,   35.1698,  76.9637, -3.0000
  GOTO/CART,   38.4947,  68.8808, -3.0000
  GOTO/CART,   44.6597,  62.6856, -3.0000
  PTMEAS/CART, 52.1338,  56.3802, -3.0000,  0.1975,  0.9803, 0.0000
ENDMES
RESUME/STOP
F(CIR2)=FEAT/CIRCLE,INNER,CART,127.0000,152.4000,-3.0000,0.0000,0.0000,1.0000, 12.7000
$$ Measurement points are created through nominal points
MEAS/CIRCLE, F(CIR2), 4
  PTMEAS/CART, 133.0087, 150.3462, -3.0000, -0.9462,  0.3234, 0.0000
  GOTO/CART,   130.3433, 152.6120, -3.0000
  GOTO/CART,   130.0076, 153.8753, -3.0000
  GOTO/CART,   129.2141, 154.9140, -3.0000
  PTMEAS/CART, 129.0538, 158.4087, -3.0000, -0.3234, -0.9462, 0.0000
  GOTO/CART,   126.7880, 155.7433, -3.0000
  GOTO/CART,   125.5247, 155.4076, -3.0000
  GOTO/CART,   124.4860, 154.6141, -3.0000
  PTMEAS/CART, 120.9913, 154.4538, -3.0000,  0.9462, -0.3234, 0.0000
  GOTO/CART,   123.6567, 152.1880, -3.0000
  GOTO/CART,   123.9924, 150.9247, -3.0000
  GOTO/CART,   124.7859, 149.8860, -3.0000
  PTMEAS/CART, 124.9462, 146.3913, -3.0000,  0.3234,  0.9462, 0.0000
ENDMES