LAB3 EIGRP1實驗

1 實驗拓撲：

2 實驗要求：

1>.R1-R3環回口0:192.168.100.x/32。

2>.R1上采用手動彙總的指令，彙總4條環回口成一條。

3>.R1上下發一條預設路由。

4>.實作R1到R2的環回口路由非等價負載。

5>.as 90都使用eigrp認證。

6>.配置R3為stub區域，且隻能發送直連和彙總路由。

7>.優化R1，R2,R3環回口，使其收不到任何eigrp封包。

8>.使用偏移清單（

offset-list）修改R2到R3環回口的metric值，增加30。

3 實驗步驟和實驗總結：

0>.基礎配置。

Router(config)#hostname R1

R1(config)#int eth0/0

R1(config-if)#ip add 100.1.1.1 255.255.255.0

R1(config-if)#no shutdown

R1(config-if)#int s1/0

R1(config-if)#ip add 12.1.1.1 255.255.255.0

R1(config-if)#no shutdown

R1(config-if)#int eth0/1

R1(config-if)#ip add 14.1.1.1 255.255.255.0

R1(config-if)#no shutdown

R1(config-if)#exit

Router(config)#hostname R2

R2(config)#int s1/1

R2(config-if)#ip add 12.1.1.2 255.255.255.0

R2(config-if)#no shutdown

R2(config-if)#exit

R2(config)#int s1/0

R2(config-if)#ip add 23.1.1.2 255.255.255.0

R2(config-if)#no shutdown

R2(config-if)#exit

R2(config)#int e0/0

R2(config-if)#ip add 100.1.1.2 255.255.255.0

R2(config-if)#no shutdown

R2(config-if)#exit

Router(config)#hostname R3

R3(config)#int s1/0

R3(config-if)#ip add 23.1.1.3 255.255.255.0

R3(config-if)#no shutdown

R3(config-if)#exit

Router(config)#hostname Internet

Internet(config)#int eth0/0

Internet(config-if)#ip add 14.1.1.4 255.255.255.0

Internet(config-if)#no shutdown

Internet(config-if)#exit

1>.R1-R3環回口0:192.168.100.x/32。

R1(config)#int loopback0

R1(config-if)#ip add 192.168.100.1 255.255.255.255

R1(config-if)#exit

R2(config)#int loopback0

R2(config-if)#ip add 192.168.100.2 255.255.255.255

R2(config-if)#exit

R3(config)#int loopback0

R3(config-if)#ip add 192.168.100.3 255.255.255.255

R3(config-if)#exit

2>.R1上采用手動彙總的指令，彙總4條環回口成一條。

R1(config)#int loopback1

R1(config-if)#ip add 192.168.0.1 255.255.255.0

R1(config-if)#int loopback2

R1(config-if)#ip add 192.168.1.1 255.255.255.0

R1(config-if)#int loopback3

R1(config-if)#ip add 192.168.2.1 255.255.255.0

R1(config-if)#int loopback4

R1(config-if)#ip add 192.168.3.1 255.255.255.0

R1(config-if)#exit

R1(config)#router eigrp 90

R1(config-router)#no auto-summary

R1(config-router)#network 192.168.100.1 0.0.0.0

R1(config-router)#network 192.168.0.1 0.0.0.255

R1(config-router)#network 192.168.0.0 0.0.255.255

R1(config-router)#network 14.1.1.0 0.0.0.255

R1(config-router)#network 100.1.1.0 0.0.0.255

R1(config-router)#network 12.1.1.0 0.0.0.255

R1(config-router)#exit

R2(config)#router eigrp 90

R2(config-router)#no auto-summary

R2(config-router)#network 100.1.1.0 0.0.0.255

R2(config-router)#network 23.1.1.0 0.0.0.255

R2(config-router)#network 192.168.0.0 0.0.255.255

R2(config-router)#network 12.1.1.0 0.0.0.255

R2(config-router)#exit

R3(config)#router eigrp 90

R3(config-router)#no auto-summary

R3(config-router)#network 192.168.100.0 0.0.0.255

R3(config-router)#network 23.1.1.0 0.0.0.255

R3(config-router)#exit

Internet(config)#router eigrp 90

Internet(config-router)#no auto-summary

Internet(config-router)#network 14.1.1.0 0.0.0.255

Internet(config-router)#exit

彙總前：

R3(config)#do show ip route

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR Gateway of last resort is not set 12.0.0.0/24 is subnetted, 1 subnets D 12.1.1.0 [90/2681856] via 23.1.1.2, 00:09:30, Serial1/0 14.0.0.0/24 is subnetted, 1 subnets D 14.1.1.0 [90/2221056] via 23.1.1.2, 00:09:30, Serial1/0 23.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C 23.1.1.0/24 is directly connected, Serial1/0 L 23.1.1.3/32 is directly connected, Serial1/0 100.0.0.0/24 is subnetted, 1 subnets D 100.1.1.0 [90/2195456] via 23.1.1.2, 00:09:30, Serial1/0 D 192.168.0.0/24 [90/2323456] via 23.1.1.2, 00:09:30, Serial1/0 D 192.168.1.0/24 [90/2323456] via 23.1.1.2, 00:09:30, Serial1/0 D 192.168.2.0/24 [90/2323456] via 23.1.1.2, 00:09:30, Serial1/0 D 192.168.3.0/24 [90/2323456] via 23.1.1.2, 00:09:30, Serial1/0 192.168.100.0/32 is subnetted, 3 subnets D 192.168.100.1 [90/2323456] via 23.1.1.2, 00:09:30, Serial1/0 D 192.168.100.2 [90/2297856] via 23.1.1.2, 00:09:30, Serial1/0 C 192.168.100.3 is directly connected, Loopback0

彙總：

R1(config)#int e0/1

R1(config-if)#ip summary-address eigrp 90 192.168.0.0/22

R1(config-if)#int e0/0

R1(config-if)#ip summary-address eigrp 90 192.168.0.0/22

R1(config-if)#int s1/0

R1(config-if)#ip summary-address eigrp 90 192.168.0.0/22

R1(config-if)#exit

彙總後：

R3(config)#do show ip route

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR Gateway of last resort is not set 12.0.0.0/24 is subnetted, 1 subnets D 12.1.1.0 [90/2681856] via 23.1.1.2, 00:15:50, Serial1/0 14.0.0.0/24 is subnetted, 1 subnets D 14.1.1.0 [90/2221056] via 23.1.1.2, 00:15:50, Serial1/0 23.0.0.0/8 is variably subnetted, 2 subnets, 2 masks C 23.1.1.0/24 is directly connected, Serial1/0 L 23.1.1.3/32 is directly connected, Serial1/0 100.0.0.0/24 is subnetted, 1 subnets D 100.1.1.0 [90/2195456] via 23.1.1.2, 00:15:50, Serial1/0 D 192.168.0.0/22 [90/2323456] via 23.1.1.2, 00:01:49, Serial1/0 192.168.100.0/32 is subnetted, 3 subnets D 192.168.100.1 [90/2323456] via 23.1.1.2, 00:15:50, Serial1/0 D 192.168.100.2 [90/2297856] via 23.1.1.2, 00:15:50, Serial1/0 C 192.168.100.3 is directly connected, Loopback0

3>.R1上下發一條預設路由。

R1(config)#ip route 0.0.0.0 0.0.0.0 14.1.1.4

R1(config)#router eigrp 90

R1(config-router)#redistribute static

R1(config-router)#exit

R3(config)# do show ip route eigrp

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR Gateway of last resort is 23.1.1.2 to network 0.0.0.0 D*EX 0.0.0.0/0 [170/2221056] via 23.1.1.2, 00:00:07, Serial1/0 12.0.0.0/24 is subnetted, 1 subnets D 12.1.1.0 [90/2681856] via 23.1.1.2, 00:25:17, Serial1/0 14.0.0.0/24 is subnetted, 1 subnets D 14.1.1.0 [90/2221056] via 23.1.1.2, 00:25:17, Serial1/0 100.0.0.0/24 is subnetted, 1 subnets D 100.1.1.0 [90/2195456] via 23.1.1.2, 00:25:17, Serial1/0 D 192.168.0.0/22 [90/2323456] via 23.1.1.2, 00:11:16, Serial1/0 192.168.100.0/32 is subnetted, 3 subnets D 192.168.100.1 [90/2323456] via 23.1.1.2, 00:25:17, Serial1/0 D 192.168.100.2 [90/2297856] via 23.1.1.2, 00:25:17, Serial1/0

4>.實作R1到R2的環回口路由非等價負載。

确認拓撲表中是否有兩條路由條目：

R1(config)#do show ip eigrp topology

EIGRP-IPv4 Topology Table for AS(90)/ID(192.168.100.1) Codes: P - Passive, A - Active, U - Update, Q - Query, R - Reply, r - reply Status, s - sia Status P 192.168.3.0/24, 1 successors, FD is 128256 via Connected, Loopback4 P 14.1.1.0/24, 1 successors, FD is 281600 via Connected, Ethernet0/1 P 192.168.2.0/24, 1 successors, FD is 128256 via Connected, Loopback3 P 192.168.0.0/22, 1 successors, FD is 128256 via Summary (128256/0), Null0 P 192.168.0.0/24, 1 successors, FD is 128256 via Connected, Loopback1 P 192.168.1.0/24, 1 successors, FD is 128256 via Connected, Loopback2 P 100.1.1.0/24, 1 successors, FD is 281600 via Connected, Ethernet0/0 P 0.0.0.0/0, 1 successors, FD is 281600 via Rstatic (281600/0) P 192.168.100.2/32, 1 successors, FD is 409600 via 100.1.1.2 (409600/128256), Ethernet0/0 via 12.1.1.2 (2297856/128256), Serial1/0 P 23.1.1.0/24, 1 successors, FD is 2195456 via 100.1.1.2 (2195456/2169856), Ethernet0/0 via 12.1.1.2 (2681856/2169856), Serial1/0 P 12.1.1.0/24, 1 successors, FD is 2169856 via Connected, Serial1/0 P 192.168.100.1/32, 1 successors, FD is 128256 via Connected, Loopback0 P 192.168.100.3/32, 1 successors, FD is 2323456 via 100.1.1.2 (2323456/2297856), Ethernet0/0 via 12.1.1.2 (2809856/2297856), Serial1/0

設定非等價負載：

R1(config)#router eigrp 90

R1(config-router)#variance 10

R1(config-router)#exit

設定後實作非等價負載：

R1(config)#do show ip route eigrp

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR Gateway of last resort is 14.1.1.4 to network 0.0.0.0 23.0.0.0/24 is subnetted, 1 subnets D 23.1.1.0 [90/2195456] via 100.1.1.2, 00:00:38, Ethernet0/0 [90/2681856] via 12.1.1.2, 00:00:38, Serial1/0 D 192.168.0.0/22 is a summary, 00:00:38, Null0 192.168.100.0/32 is subnetted, 3 subnets D 192.168.100.2 [90/409600] via 100.1.1.2, 00:00:38, Ethernet0/0 [90/2297856] via 12.1.1.2, 00:00:38, Serial1/0 D 192.168.100.3 [90/2323456] via 100.1.1.2, 00:00:38, Ethernet0/0 [90/2809856] via 12.1.1.2, 00:00:38, Serial1/0

R1(config)#do show ip route 192.168.100.2

Routing entry for 192.168.100.2/32 Known via "eigrp 90", distance 90, metric 409600, type internal Redistributing via eigrp 90 Last update from 12.1.1.2 on Serial1/0, 00:01:05 ago Routing Descriptor Blocks: * 100.1.1.2, from 100.1.1.2, 00:01:05 ago, via Ethernet0/0 Route metric is 409600, traffic share count is 240 Total delay is 6000 microseconds, minimum bandwidth is 10000 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1 12.1.1.2, from 12.1.1.2, 00:01:05 ago, via Serial1/0 Route metric is 2297856, traffic share count is 43 Total delay is 25000 microseconds, minimum bandwidth is 1544 Kbit Reliability 255/255, minimum MTU 1500 bytes Loading 1/255, Hops 1

5>.as 90都使用eigrp認證。

R2(config)#key chain glab

R2(config-keychain)#key 1

R2(config-keychain-key)#key-string galb123

R2(config-keychain-key)#exit

R2(config-keychain)#key 2

R2(config-keychain-key)#key-string glab123

R2(config-keychain-key)#exit

R2(config)#int s1/0

R2(config-if)#ip authentication key-chain eigrp 90 glab

R2(config-if)#ip authentication mode eigrp 90 md5

R2(config-if)#exit

R3(config)#key chain glab1

R3(config-keychain)#key 1

R3(config-keychain-key)#key-string galb123

R3(config-keychain-key)#exit

R3(config-keychain)#key 2

R3(config-keychain-key)#key-string glab123

R3(config-keychain-key)#exit

R3(config)#int s1/0

R3(config-if)#ip authentication key-chain eigrp 90 glab1

R3(config-if)#ip authentication mode eigrp 90 md5

R3(config-if)#exitR2(config)#do show ip eigrp neighbors

EIGRP-IPv4 Neighbors for AS(90) H Address Interface Hold Uptime SRTT RTO Q Seq (sec) (ms) Cnt Num 2 23.1.1.3 Se1/0 12 00:00:29 26 156 0 10 1 12.1.1.1 Se1/1 13 01:00:23 14 100 0 39 0 100.1.1.1 Et0/0 12 01:01:16 6 100 0 38

R2(config)#int s1/1

R2(config-if)#ip authentication key-chain eigrp 90 glab

R2(config-if)#ip authentication mode eigrp 90 md5

R2(config-if)#exit

R1(config)#key chain glab1

R1(config-keychain)#key 1

R1(config-keychain-key)#key-string galb123

R1(config-keychain-key)#exit

R1(config-keychain)#key 2

R1(config-keychain-key)#key-string glab123

R1(config-keychain-key)#exit

R1(config-keychain)#exit

R1(config)#int e0/1

R1(config-if)#ip authentication key-chain eigrp 90 glab1

R1(config-if)#ip authentication mode eigrp 90 md5

R1(config-if)#exit

R1(config)#int s1/0

R1(config-if)#ip authentication key-chain eigrp 90 glab1

R1(config-if)#ip authentication mode eigrp 90 md5

R1(config-if)#exi

Internet(config)#key chain glab1

Internet(config-keychain)#key 1

Internet(config-keychain-key)#key-string galb123

Internet(config-keychain-key)#exit

Internet(config-keychain)#key 2

Internet(config-keychain-key)#key-string glab123

Internet(config-keychain-key)#exit

Internet(config-keychain)#exit

Internet(config)#int e0/0

Internet(config-if)#ip authentication key-chain eigrp 90 glab1

Internet(config-if)#ip authentication mode eigrp 90 md5

Internet(config-if)#exit

6>.配置R3為stub區域，且隻能發送直連和彙總路由。

R3(config)#router eigrp 90

R3(config-router)#eigrp stub

R3(config-router)#do show run | se eigrp

ip authentication mode eigrp 90 md5 ip authentication key-chain eigrp 90 glab1 router eigrp 90 network 23.1.1.0 0.0.0.255 network 192.168.100.0 eigrp stub connected summary

7>.優化R1，R2,R3環回口，使其收不到任何eigrp封包。

R3(config)#router eigrp 90

R3(config-router)#passive-interface loopback0

R3(config-router)#exit

R2(config)#router eigrp 90

R2(config-router)#passive-interface loopback0

R2(config-router)#exit

R1(config-if)#router eigrp 90

R1(config-router)#passive-interface loopback0

R1(config-router)#exit

8>.使用偏移清單（offset-list）修改R2到R3環回口的metric值，增加30。

R2(config)#access-list 1 permit 192.168.100.3

R2(config)#router eigrp 90

R2(config-router)#offset-list 1 in 30 serial 1/0

R2(config-router)#do show ip rout eigrp

Codes: L - local, C - connected, S - static, R - RIP, M - mobile, B - BGP D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2 E1 - OSPF external type 1, E2 - OSPF external type 2 i - IS-IS, su - IS-IS summary, L1 - IS-IS level-1, L2 - IS-IS level-2 ia - IS-IS inter area, * - candidate default, U - per-user static route o - ODR, P - periodic downloaded static route, H - NHRP, l - LISP a - application route + - replicated route, % - next hop override, p - overrides from PfR Gateway of last resort is 100.1.1.1 to network 0.0.0.0 D*EX 0.0.0.0/0 [170/307200] via 100.1.1.1, 00:12:45, Ethernet0/0 14.0.0.0/24 is subnetted, 1 subnets D 14.1.1.0 [90/307200] via 100.1.1.1, 00:12:45, Ethernet0/0 D 192.168.0.0/22 [90/409600] via 100.1.1.1, 00:12:45, Ethernet0/0 192.168.100.0/32 is subnetted, 3 subnets D 192.168.100.1 [90/409600] via 100.1.1.1, 00:12:45, Ethernet0/0 D 192.168.100.3 [90/2297886] via 23.1.1.3, 00:00:11, Serial1/0

4.作業中遇到的問題：

無