个人安装环境:
OS:CentOS6.7 64位
FreeSWITCH Ver:1.6.17
一. 编译出错
安装 之前, 最好 先安装 这几个东西(如果有, 请忽略):
yasm (有nasm的话 不用装这个) ,
opus-devel(可能 提示 libopus-dev 或 libopus-devel 等) ,
lua-devel , libsndfile-devel , libtiff-devel
当然了, 你也可以 先不管, 等 出错 提示了, 在按照下面的方法安装:
1. 安装 yasm , yasm 和 nasm 必须要有一个,必须装了!
错误提示: Neither yasm nor nasm have been found
((which nasm) || (which yasm) || (git clone https://github.com/yasm/yasm.git && cd yasm && ./autogen.sh && make && make install))
2.安装 lua-devel
错误提示: 找不到 lua.h 等lua的头文件
yum install lua lua-devel
3.安装 opus-devel
错误提示: You must install libopus-dev to build mod_opus
yum -y install opus-devel
#可能需要清理: make clean && ./configure && make
如果还是报这个错误, 就注释这两行,在Makefile:
vim freeswitch/src/mod/codecs/mod_opus/Makefile
# Comment line 896 & 897
#install: error
#all: error
4.安装 sndfile
错误提示 : You must install libsndfile-dev to build mod_sndfile
#下载包libsndfile-x.x.xx.tar.gz from地址 http://www.mega-nerd.com/libsndfile/#Download, 然后
tar zxvf libsndfile-1.0.26.tar.gz
./configure
make
make install
cp /usr/local/lib/pkgconfig/sndfile.pc /usr/lib64/pkgconfig
#然后 重新 configure FreeSWITCH...
如果还是报这个错误,就注释这两行,在Makefile:
vim src/mod/formats/mod_sndfile/Makefile
# Comment line 897 & 898
#install: error
#all: error
5.安装 libyuv
错误提示: You must install libyuv-dev to build mod_fsv
cd freeswitch/libs
git clone https://freeswitch.org/stash/scm/sd/libyuv.gitcd libyuv
make -f linux.mk CXXFLAGS="-fPIC -O2 -fomit-frame-pointer -Iinclude/"
make install
cp /usr/lib/pkgconfig/libyuv.pc /usr/lib64/pkgconfig/
6.安装 libvpx
错误提示: You must install libvpx-dev to build ....
cd freeswitch/libs
git clone https://freeswitch.org/stash/scm/sd/libvpx.git
cd libvpx
./configure --enable-pic --disable-static --enable-shared
make
make install
cp /usr/local/lib/pkgconfig/vpx.pc /usr/lib64/pkgconfig/
7.安装 libpng
错误提示: You must install libpng-dev to build ....
git clone https://freeswitch.org/stash/scm/sd/libpng.git
cd libpng
./configure
make
make install
cp /usr/local/lib/pkgconfig/libpng* /usr/lib64/pkgconfig/
8.安装 libav
错误提示: You must install libav-dev to build ....
git clone https://freeswitch.org/stash/scm/sd/libav.git
cd libav
./configure #CFLAGS="-fPIC" ./configure --enable-pic --enable-shared
make # make CXXFLAGS="-fPIC"
make install
二. 其他问题
1.错误提示: libs/spandsp
configure: loading cache ../../config.cache
configure: error: `CFLAGS‘ was not set in the previous run
configure: error: `CPPFLAGS‘ was not set in the previous run
configure: error: in `/usr/src/freeswitch.git/libs/spandsp‘:
configure: error: changes in the environment can compromise the build
configure: error: run `make distclean‘ and/or `rm ../../config.cache‘ and start over
解决: 重新 configure
./configure -C && make
三. 安装中文语音
fs默认不加载中文语音。需要在fs的src中首先编译中文模块。
1.编译:
a.在 configure 之前, 编辑 modules.conf, 取消 "#say/mod_say_zh" 这行的注释 ->"say/mod_say_zh"
b.补救安装 `make mod_say_zh-install`
2.加载(不重启fs)
在fs控制台上加载该模块 `load mod _say_zh`
若想fs在每次启动的时候都加载该模块,就在`autoload_configs/modules.conf.xml`中``的注释去掉即可。
也可以这样:
sed -i ‘s###g‘ autoload_configs/modules.conf.xml
3.修改 `var.xml`中的配置
``修改为中文语音文件的目录
``
加入以下几行(也可以不加)
4.加入中文语音配置
cd conf/lang
cp -R en zh
mv zh/en.xml zh/zh.xml
vim zh/zh.xml
(替换路径`en/us/callie`和 `en`等:第二行修改为)
5. 载入中文配置
在`freeswitch.xml`的`
` `
四. 解决ESL拒绝连接问题
默认是只接受本机连接的,稍一改动就 内外都不能连接了,或者只能接受内外之一连接
解决方法:
1. event_socket.conf.xml 加入:
2. acl.conf.xml 加入: