“Embroidery”
Embroidery is a general term for needlework embroidering patterns on fabrics. It is the art of needles and threads that add human design and fabrication to fabrics.
The first thing we come into contact with in computer embroidery plate making is embroidery stitching, with the continuous upgrading of computer embroidery software, stitching is also constantly enriching and expanding. From the initial simple single needle, double needle, three needles to the later flat bag needle, ta ta meter and now E needle, weekly needle, curve ta ta meter, insert needle, cloud needle and other stitches. The effect of computer embroidery patterns is also easier to achieve due to the variability and flexibility of stitching.
Single needle
It is used to embroider some relatively thin line segments, often used in the bottom line or in the hemming. It is also possible to add a flower plate to produce a special stitch effect. The needle step of the single needle is set by the system, and when there is a sharp turn in the graphic, the needle step of the single needle can be appropriately reduced.
The main parameters of a single needle:
1. Maximum step size: refers to the maximum distance that the embroidery function can move.
2. Minimum stitch step: refers to the minimum distance that the embroidery function can move.
3. The step size of the single needle: refers to the distance from each point to the point of the single needle.
Manual single needle
The manual single needle is not limited by the settings in the system and can be taken in any long and arbitrary angle. It differs from a single needle in that between two input points in the arbitrariness, there is no lower needle point. It is generally used for the connection between short distances of flower plates, and the role is equivalent to not cutting a jumper!
Needles
Needle is the most common stitching method, in some places also called "flat package needle", needle is mainly used to embroider narrow strip patterns, the sense of line and three-dimensional sense of the needle are very strong, good coverage. When filling a wider shape with a needle, the stitch line becomes fluffy, affecting the beauty of the embroidery, which is the reason why the needle is not suitable for embroidering wide shapes.
Pin-to-pin parameters
1. Number of repetitions
Refers to the number of times the embroidery is repeated by needle
2. Density
Pin density is the distance between two points adjacent to the border. A larger value indicates that the stitches are sparser, and a smaller value indicates that the stitches are denser
3. Gradient density
Using gradient density can produce the artistic effect of thin variations of colors
He he's rice
Ta ta meters are mainly used to fill large areas or irregular closed shapes, which are composed of single needles in a special arrangement, and the stitches of each column are arranged according to a certain offset value, thus avoiding the obvious splitting line in the figure. His stitches are arranged compactly and parallelly.
Ta tammy parameters:
1. Tatami density
The density of his meters refers to the distance between two adjacent stitch lines in the same direction as his other meters
2. Texture
The grains of his tamme include twill and patterns
Although the primer is not visible in the final embroidery product, the primer plays an important role in the design.
You can only embroider a high-quality, professional-grade embroidery product if you correctly use the type and quantity of primer stitches in the pattern of each filler needle. Reducing the number of stitches by eliminating primer stitches can only reduce the quality of the final product. The stitches are very loose fill stitches, or just flat stitches.
The main uses of primer stitches are:
1: Stabilize the base fabric, which can greatly reduce the influence of embroidery thread on the stretch of the base cloth fabric.
2: Pad the surface stitches and prevent them from falling into the softer or thicker fabric of the base cloth. A way to reduce stitches, reduce costs, reduce downtime, and improve efficiency.
A, minus the unnecessary base, change the needle density, such as the original ta ta meter 0.4, can be changed to 0.45, 0.5.
B. Use the stitch processor to reduce the needle for the pattern as a whole.
C. Remove unnecessary wire cutting codes and color change codes, and reduce the number of wire cuts and color changes, which is to reduce the number of downtimes.
D, in the design of the pattern should pay attention to the order of the pattern, so that you can save a lot of time, the traces inside can be 3.5-5 mm needle length, can improve the speed.
E-pin
The E-pin looks a lot like a comb and is mainly used on the edges or on loosely embroidered figures. The most commonly used is in the embroidery of the edge of the bag, in order to E stitches can better follow the graphic boundaries, you can insert a few single stitches in the E stitches.
Main parameters:
1. The step size of the E-shaped needle: refers to the distance between two adjacent lower needle points on the same stitch line.
2.E-stitch stitch density refers to the distance between two adjacent pin drop points on the first border of digitization when the number of single stitches is 1.
Stitching is the soul of computer embroidery,
Stitching is like a knife in the hands of a sculptor,
The baton in the hands of the conductor,
All the miraculous effects are born of it
A series of ingenious embroideries come from it.
Therefore, it is very important to be proficient in various stitches when designing and to use stitches in combination freely.
Disclaimer: Some of the images and text are from the Internet and are for study and research purposes only. We respect the copyright of each author, if there is any suspected infringement, please contact in time, we will remove it as soon as possible.