How to make WiFi use without dead ends
How to make WiFi use without dead ends? The following is the wireless routing bridging method shared by Xiaobian, you can refer to it. With the continuous improvement of the living standards of our people, the per capita housing area of the masses is getting larger and larger, which has also caused some problems in life, such as the wireless router signal can not be kept stable in all rooms. In order to improve this situation, Xiaobian will introduce to netizens the method of bridging with more than two wireless routers, which will solve the problem of WiFi signal dead end or weakening... End of broadcast chamber. Here are two ways to summarize:
Method one
I have listed it for everyone with pictures, so that you can save and use it.
Method two
For most users, if the signal strength of one router is not enough, two or three routers should be able to ensure that there is enough signal strength in all rooms. Of course, if your family's deep house compound, the area is very large, more than ten thousand into, and even the courtyard has to be connected to high-speed, high-speed rail, and airport... That may require an enterprise-level network setup, which is beyond the scope of this article, and it is recommended to hire a professional to build it.
Xiaobian takes two routers as an example (three, four, etc. are a truth) to introduce the basic method of home wireless router bridging. It should be noted that because each router product has its own advantages, the router debugging page may look different, but the content that needs to be adjusted is the same, so users need to be flexible. In addition, ensuring that each secondary router has WDS capabilities is the key to successful bridging.
The specific steps are as follows:
1. Enter the main router settings page and record the SSID (wireless name of the router) and the channel number
Tip 1: Entering the router settings interface is generally achieved by entering an IP address such as 192.168.1.1 in the browser. Of course, in general, the ip address of the router is the one mentioned earlier, but there are many exceptions, and the specific situation requires the user to refer to the router manual.
▲In order to make it easier to distinguish, change the main route address to 10.1.1.2, and restart the router after modification
Xiaobian tip 2: the router's own 'wireless name can be changed, this is generally completed after buying the router to set up the wireless network, of course, you can also change it at any time.
Xiaobian tip 3: The general router will set the channel number to automatic by default, which is a workaround, because the channels between different independent routers can only be different to not conflict. For example, many urban users are now using routers in buildings and apartments, and the signals of left and right neighbors are crisscrossed, so it is also necessary for the router to use "automatic" to set the available channel by default.
Tips 4: For the situation mentioned in this article, it is best to manually set the available channels, because the master-slave wireless router must ensure that the channels are the same to complete the bridging, and the method is not difficult, such as holding the mobile phone next to the router to test, if the channel is available, the mobile phone can access the Internet through this router. After determining the available channels, as long as the router is not turned off, this channel number is occupied by your router, and you don't have to worry about the routers of the neighbors "grabbing the line".
2. Enter the secondary router settings page, change the setting page address to a different IP address from the main router, open WDS, and set the same channel number as the main router
Xiaobian tip 5: The main router does not have to open WDS, because it does not have to undertake other people's WiFi signals, so it does not matter whether there is a WDS function or not.
Xiaobian tip 6: change the IP address of the secondary router, pay attention to the main router to maintain the same address segment, such as the main router is 192.168.1.1, the secondary router can be set to 192.168.1.2, that is, the last bit can theoretically be set to 2 ~ 255, the specific settings also need to refer to the network environment.
Method 1:
▲The SECONDARY ROUTER IP address was changed to 10.1.1.3
Tip 7: The secondary router channel number needs to be set to the same as the main router, do not use the default "automatic", the setting method is the same as the main router channel number.
3. Scan the WDS main router signal in the secondary router, find your own main router from the results after scanning, and then connect
Tip 8: The secondary router SSID does not need to be the same as the main router. Of course, many online tutorials say that they should be set to be consistent, and the reason why other gods write this should be to take into account that the main and secondary router signals with the same name and password under the same roof can be seamlessly connected. However, if the two routers are different in name, the user himself can understand which router is connected to, and if there is a problem, it is better to press Tu Suoji. Therefore, the two options have their own advantages, and you decide for yourself.
Tip 9: The secondary router password does not need to be the same as the main router, but in order to facilitate memory and other reasons, it can also be set to the same, which is not a matter of principle, it all depends on the user's wishes.
Tip 10: The DHCP of the secondary router can be stopped or not stopped, and the function is to dynamically assign IP addresses. If this function is turned off, the IP address of the connected router device is uniformly assigned by the main router; If this function is enabled, the user needs to manually divide the pool of IP addresses that can be assigned by the primary and secondary routers to prevent IP address distribution conflicts, such as the main router is responsible for 192.168.1.10~69, and the secondary router is responsible for allocating 192.168.1.70~119 (for example, the user is flexible).
▲Example of router address pool assignment
Xiaobian tip 11: If the main router is found to be on the network after restarting, it may be that the channel is occupied, and at this time, you should manually find the appropriate channel again, the method is the same as Tip 4.
Tip 12: If the main router before bridging is set up with an anti-scratching network and MAC address filtering is enabled, you need to turn off the function or update the filtering rules, and add the whitelist after finding the appropriate MAC address of the secondary router to make the bridging successful.
At this time, the settings of the secondary router take effect, and you can try to connect with a device such as a mobile phone. The secondary router and the main router can not be connected with a network cable to prevent the occurrence of "network storms", and the choice of this wireless relay method is because of the avoidance of wiring troubles, so there is no need to add snakes. It is best to have fewer partition walls between routers to avoid signal attenuation, and it needs to be guaranteed to be within the effective distance. If you want to add a secondary router, you can connect with the main router first in the above way, and the parallel connection method within the effective range of the main router is better.
Today's content is like this, I hope to help you, what questions can leave a message to me, thank you for the support of fans and friends your attention is my motivation!