源碼和工具打包:[CSND下載下傳]荔枝派nano彙總資料(uboot、主線Linux、buildroot及dl包、編譯燒錄工具、配置及燒錄檔案)
一、下載下傳源碼
# 首先安裝一些依賴,比如linux頭檔案:
sudo apt-get install linux-headers-$(uname -r)
# 下載下傳解壓
wget https://buildroot.org/downloads/buildroot-2017.08.tar.gz
tar xvf buildroot-2017.08.tar.gz
二、圖形配置
cd buildroot-2017.08/
# 下載下傳預設配置檔案 buildroot.config
wget https://fdvad021asfd8q.oss-cn-hangzhou.aliyuncs.com/migrate/buildroot.config
# 複制一個并重命名
cp buildroot.config .config
# 圖形界面配置
make menuconfig
配置界面:
Target options --->
Target Architecture Variant (arm926t) ---> # arm926ejs架構
[ ] Enable VFP extension support # Nano 沒有 VFP單元,勾選會導緻某些應用無法運作
Target ABI (EABI) --->
Floating point strategy (Soft float) ---> // 軟浮點
System configuration --->
(Lichee Pi) System hostname // hostname
(licheepi) Root password // 預設賬戶為root 密碼為licheepi
[*] remount root filesystem read-write during boot // 啟動時重新挂在檔案系統使其可讀寫
三、軟體包
- 編譯時會下載下傳很多軟體包,速度很慢,可以先下載下傳下來:【dl包】百度網盤下載下傳
- 解壓出
檔案夾放在dl
根目錄下buildroot-2017.08
- 在編譯的時候發現在下載下傳
,是以這個也要放入arm-2014.05-29-arm-none-linux-gnueabi-i686-pc-linux-gnu.tar.bz2
檔案夾裡(編譯時會自動解壓)。dl
- 這些資料在文章第一行連結裡面全部打包了。
四、編譯
# buildroot不能進行多線程編譯
make
第一次編譯失敗,不清楚是否虛拟機崩潰引起的,
make clean
再次
make
就編譯成功了。
編譯完成的鏡像包在
buildroot-2017.08 ‣ output ‣images ‣ rootfs.tar
(大小98.1MB)
五、燒錄
參考:全志F1C100S/F1C200S學習筆記(2)——TF/SD卡分區及系統建構燒錄
使用TF卡燒錄。
六、啟動LOG
賬号:
root
密碼:
licheepi
U-Boot SPL 2018.01-05679-g013ca457fd-dirty (Jan 28 2021 - 17:16:00)
DRAM: 64 MiB
Trying to boot from MMC1
U-Boot 2018.01-05679-g013ca457fd-dirty (Jan 28 2021 - 17:16:00 +0800) Allwinner Technology
CPU: Allwinner F Series (SUNIV)
Model: Lichee Pi Nano
DRAM: 64 MiB
MMC: SUNXI SD/MMC: 0
SF: unrecognized JEDEC id bytes: 00, c8, f1
*** Warning - spi_flash_probe_bus_cs() failed, using default environment
Setting up a 480x272 lcd console (overscan 0x0)
In: [email protected]
Out: [email protected]
Err: [email protected]
Net: No ethernet found.
starting USB...
No controllers found
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:1...
Found U-Boot script /boot.scr
reading /boot.scr
280 bytes read in 16 ms (16.6 KiB/s)
## Executing script at 80c50000
reading suniv-f1c100s-licheepi-nano.dtb
8035 bytes read in 27 ms (290 KiB/s)
reading zImage
3836208 bytes read in 202 ms (18.1 MiB/s)
## Flattened Device Tree blob at 80c00000
Booting using the fdt blob at 0x80c00000
Loading Device Tree to 816fb000, end 816fff62 ... OK
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.15.0-rc8-licheepi-nano+ ([email protected]) (gcc version 7.2.1 20171011 (Linaro GCC 7.2-2017.11)) #2 Mon Jan 25 11:04:40 CST 2021
[ 0.000000] CPU: ARM926EJ-S [41069265] revision 5 (ARMv5TEJ), cr=0005317f
[ 0.000000] CPU: VIVT data cache, VIVT instruction cache
[ 0.000000] OF: fdt: Machine model: Lichee Pi Nano
[ 0.000000] Memory policy: Data cache writeback
[ 0.000000] random: fast init done
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=tty1 console=ttyS1,115200 panic=5 rootwait root=/dev/mmcblk0p2 rw
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Memory: 55164K/65536K available (6144K kernel code, 236K rwdata, 1388K rodata, 1024K init, 244K bss, 10372K reserved, 0K cma-reserved, 0K highmem)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
[ 0.000000] vmalloc : 0xc4800000 - 0xff800000 ( 944 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xc4000000 ( 64 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .text : 0x(ptrval) - 0x(ptrval) (7136 kB)
[ 0.000000] .init : 0x(ptrval) - 0x(ptrval) (1024 kB)
[ 0.000000] .data : 0x(ptrval) - 0x(ptrval) ( 237 kB)
[ 0.000000] .bss : 0x(ptrval) - 0x(ptrval) ( 245 kB)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
[ 0.000048] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 89478484971ns
[ 0.000116] clocksource: timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[ 0.000666] Console: colour dummy device 80x30
[ 0.001591] console [tty1] enabled
[ 0.001698] Calibrating delay loop... 203.16 BogoMIPS (lpj=1015808)
[ 0.070295] pid_max: default: 32768 minimum: 301
[ 0.070635] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.070727] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.072203] CPU: Testing write buffer coherency: ok
[ 0.073926] Setting up static identity map for 0x80100000 - 0x80100058
[ 0.076565] devtmpfs: initialized
[ 0.083193] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.083362] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.083675] pinctrl core: initialized pinctrl subsystem
[ 0.085777] NET: Registered protocol family 16
[ 0.087296] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.089176] cpuidle: using governor menu
[ 0.115316] SCSI subsystem initialized
[ 0.115733] usbcore: registered new interface driver usbfs
[ 0.115952] usbcore: registered new interface driver hub
[ 0.116211] usbcore: registered new device driver usb
[ 0.116719] pps_core: LinuxPPS API ver. 1 registered
[ 0.116802] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[ 0.116932] PTP clock support registered
[ 0.117434] Advanced Linux Sound Architecture Driver Initialized.
[ 0.119016] clocksource: Switched to clocksource timer
[ 0.145398] NET: Registered protocol family 2
[ 0.146900] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.147054] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.147144] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.147474] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.147580] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.148107] NET: Registered protocol family 1
[ 0.149566] RPC: Registered named UNIX socket transport module.
[ 0.149681] RPC: Registered udp transport module.
[ 0.149733] RPC: Registered tcp transport module.
[ 0.149775] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.152058] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.153953] Initialise system trusted keyrings
[ 0.154594] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.172172] NFS: Registering the id_resolver key type
[ 0.172330] Key type id_resolver registered
[ 0.172387] Key type id_legacy registered
[ 0.185896] Key type asymmetric registered
[ 0.186004] Asymmetric key parser 'x509' registered
[ 0.186249] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251)
[ 0.186349] io scheduler noop registered
[ 0.186394] io scheduler deadline registered
[ 0.187185] io scheduler cfq registered (default)
[ 0.187276] io scheduler mq-deadline registered
[ 0.187328] io scheduler kyber registered
[ 0.188488] sun4i-usb-phy 1c13400.phy: Couldn't request ID GPIO
[ 0.198180] suniv-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
[ 0.368065] Serial: 8250/16550 driver, 8 ports, IRQ sharing disabled
[ 0.395073] 1c25000.serial: ttyS0 at MMIO 0x1c25000 (irq = 23, base_baud = 6250000) is a 16550A
[ 0.417862] 1c25400.serial: ttyS1 at MMIO 0x1c25400 (irq = 24, base_baud = 6250000) is a 16550A
[ 0.894866] console [ttyS1] enabled
[ 0.905638] panel-simple panel: panel supply power not found, using dummy regulator
[ 0.915162] SCSI Media Changer driver v0.25
[ 0.923069] m25p80 spi0.0: unrecognized JEDEC id bytes: 00, c8, f1
[ 0.930040] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.936638] ehci-platform: EHCI generic platform driver
[ 0.942309] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.948595] ohci-platform: OHCI generic platform driver
[ 0.954380] usbcore: registered new interface driver usb-storage
[ 0.961546] udc-core: couldn't find an available UDC - added [g_cdc] to list of pending drivers
[ 0.970714] i2c /dev entries driver
[ 1.029147] sunxi-mmc 1c0f000.mmc: base:0x6917abdb irq:19
[ 1.036689] usbcore: registered new interface driver usbhid
[ 1.042462] usbhid: USB HID core driver
[ 1.064559] NET: Registered protocol family 17
[ 1.069471] Key type dns_resolver registered
[ 1.076088] Loading compiled-in X.509 certificates
[ 1.094618] sun4i-drm display-engine: bound 1e60000.display-backend (ops 0xc07394b8)
[ 1.103583] sun4i-drm display-engine: bound 1c0c000.lcd-controller (ops 0xc073879c)
[ 1.111457] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 1.118115] [drm] No driver support for vblank timestamp query.
[ 1.172361] Console: switching to colour frame buffer device 60x34
[ 1.172736] mmc0: host does not support reading read-only switch, assuming write-enable
[ 1.175040] mmc0: new high speed SDHC card at address b368
[ 1.176155] mmcblk0: mmc0:b368 NCard 29.1 GiB
[ 1.178482] mmcblk0: p1 p2
[ 1.241939] sun4i-drm display-engine: fb0: frame buffer device
[ 1.261409] [drm] Initialized sun4i-drm 1.0.0 20150629 for display-engine on minor 0
[ 1.283077] usb_phy_generic usb_phy_generic.0.auto: usb_phy_generic.0.auto supply vcc not found, using dummy regulator
[ 1.313876] musb-hdrc musb-hdrc.1.auto: MUSB HDRC host driver
[ 1.332630] musb-hdrc musb-hdrc.1.auto: new USB bus registered, assigned bus number 1
[ 1.355729] hub 1-0:1.0: USB hub found
[ 1.366323] hub 1-0:1.0: 1 port detected
[ 1.378458] using random self ethernet address
[ 1.389544] using random host ethernet address
[ 1.402138] usb0: HOST MAC ba:67:02:6b:d6:15
[ 1.412981] usb0: MAC 5a:bf:df:fb:6d:e1
[ 1.423277] g_cdc gadget: CDC Composite Gadget, version: King Kamehameha Day 2008
[ 1.443255] g_cdc gadget: g_cdc ready
[ 1.454176] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[ 1.484188] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[ 1.503351] ALSA device list:
[ 1.512580] #0: Loopback 1
[ 1.522412] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[ 1.543220] cfg80211: failed to load regulatory.db
[ 1.557211] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
[ 1.611234] EXT4-fs (mmcblk0p2): warning: mounting fs with errors, running e2fsck is recommended
[ 1.662075] EXT4-fs (mmcblk0p2): recovery complete
[ 1.673237] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
[ 1.693549] VFS: Mounted root (ext4 filesystem) on device 179:2.
[ 1.728163] devtmpfs: mounted
[ 1.741866] Freeing unused kernel memory: 1024K
[ 1.941203] EXT4-fs (mmcblk0p2): re-mounted. Opts: data=ordered
Starting logging: OK
Initializing random number generator... done.
[ 7.677011] random: crng init done
[ 305.129055] EXT4-fs (mmcblk0p2): error count since last fsck: 14
[ 305.146504] EXT4-fs (mmcblk0p2): initial error at time 1611891021: ext4_validate_block_bitmap:376
[ 305.167182] EXT4-fs (mmcblk0p2): last error at time 1611901992: ext4_validate_block_bitmap:376
如果shell終端無法控制,需要做以下修改:
全志F1C100S/F1C200S學習筆記(10)——buildroot更改預設終端序列槽為uart1