本文來源：http://gl.ict.usc.edu/Research/3DDisplay/
Rendering for an Interactive 360º Light Field Display
SIGGRAPH 2007 Papers Proceedings
SIGGRAPH 2007 Emerging Technologies
| Andrew Jones Ian McDowall* Hideshi Yamada** Mark Bolas*** Paul Debevec |
| USC Institute for Creative Technologies *Fakespace Labs, Inc. **Sony Corporation ***USC School of Cinematic Arts |
NEW!
Live 3D Teleconferencing
INTRODUCTION:
The Graphics Lab at the University of Southern California has designed an easily reproducible, low-cost 3D display system with a form factor that offers a number of advantages for displaying 3D objects in 3D. The display is:
- autostereoscopic - requires no special viewing glasses
- omnidirectional - generates simultaneous views accomodating large numbers of viewers
- interactive - can update content at 200Hz
The system works by projecting high-speed video onto a rapidly spinning mirror. As the mirror turns, it reflects a different and accurate p_w_picpath to each potential viewer. Our rendering algorithm can recreate both virtual and real scenes with correct occlusion, horizontal and vertical perspective, and shading.
While flat electronic displays represent a majority of user experiences, it is important to realize that flat surfaces represent only a small portion of our physical world. Our real world is made of objects, in all their three-dimensional glory. The next generation of displays will begin to represent the physical world around us, but this progression will not succeed unless it is completely invisible to the user: no special glasses, no fuzzy pictures, and no small viewing zones.
ABSTRACT:
We describe a set of rendering techniques for an autostereoscopic light field display able to present interactive 3D graphics to multiple simultaneous viewers 360 degrees around the display. The display consists of a high-speed video projector, a spinning mirror covered by a holographic diffuser, and FPGA circuitry to decode specially rendered DVI video signals. The display uses a standard programmable graphics card to render over 5,000 p_w_picpaths per second of interactive 3D graphics, projecting 360-degree views with 1.25 degree separation up to 20 updates per second. We describe the system's projection geometry and its calibration process, and we present a multiple-center-of-projection rendering technique for creating perspective-correct p_w_picpaths from arbitrary viewpoints around the display. Our projection technique allows correct vertical perspective and parallax to be rendered for any height and distance when these parameters are known, and we demonstrate this effect with interactive raster graphics using a tracking system to measure the viewer's height and distance. We further apply our projection technique to the display of photographed light fields with accurate horizontal and vertical parallax. We conclude with a discussion of the display's visual accommodation performance and discuss techniques for displaying color p_w_picpathry.
HIGH-SPEED DLP PROJECTION USING STANDARD GRAPHICS HARDWARE:
We achieve high speed video projection by modifying an off-the-shelf projector to use a new DLP drive card with custom programmed FPGA-based circuitry. The projector decodes a standard DVI signal from the graphics card. Instead of rendering a color p_w_picpath, the projector takes each 24-bit color frame of video and displays each bit sequentially as separate frames. Thus, if the incoming digital video signal is 60Hz, the projector displays 60?24 = 1,440 frames per second. To achieve faster rates, the video card?s output is set to rates of 200Hz and above. At 200Hz, the projector displays 4,800 binary frames per second.
ANISOTROPIC SPINNING MIRROR:
Previous volumetric displays used a spinning diffuse plane to scatter light in all directions but could not recreate view-dependent effects such as occlusion. Instead, we use an anisotropic holographic diffuser bonded onto a first surface mirror. Horizontally, the mirror is sharply specular to maintain a 1.25 degree separation between views. Vertically, the mirror scatters widely so the projected p_w_picpath can be viewed from multiple heights.
This surface spins synchronously relative to the p_w_picpaths being displayed by the projector. We use the PC video output rate as the master signal. The projector's FPGA decodes the current frame rate and interfaces directly to an Animatics SM3420D "Smart Motor". As the mirror rotates up to 20 times per second, persistence of vision creates the illusion of a floating object at the center of the mirror.
CORRECT PERSPECTIVE WITH VERTICAL TRACKING:
The p_w_picpaths sent to the projector can either be pre-computed or rendered in real-time using raster OpenGL graphics. The simplest rendering algorithm projects a sequence of 288 perspective p_w_picpaths from a camera rotating around the scene. This perspective geometry assumes that all rays reflected off the mirror reconverge at a single viewpoint. In reality, frames reflected off the mirror diverge towards multiple viewpoints in space. The result (shown on the left) is a 3D p_w_picpath where the horizontal field of view is exaggerated and straight lines appear curved. A second artifact is due to the lack of vertical parallax. Just as an p_w_picpath on a piece of paper will appear smaller when viewed from an oblique angle, the projected p_w_picpath will appear to stretch vertically when the viewer changes height. We have developed an improved rendering algorithm (shown on the right) that generates correct horizontal and vertical perspective at multiple heights. Instead of using a simple perspective camera, we trace each reflected projector ray to find the correct viewer positions at a given moment in time. Furthermore, we leverage our system's unique real-time update to dynamically adjust the p_w_picpathry based on each viewer?s height and distance. This is a novel and promising way of displaying 3D p_w_picpathry. If combined with a passive tracking system, it allows multiple tracked viewers to each experience his own correct view of a three-dimensional scene, with horizontal and vertical parallax, without 3D glasses.
MATERIALS:
High Resolution Images:
| | | | |
| download |
| | |
SIGGRAPH 2007 Paper:
- 3DDisplay_USCICT_SIGGRAPH2007.pdf, 1.9MB. ( Adobe Acrobat )
360 Display Video Two Minute Version:
- 3DDisplay_USCICT_SIGGRAPH2007_Subtitles.mov, 234MB. 1:53 min ( Quicktime )
- 3DDisplay_USCICT_SIGGRAPH2007_NoSubtitles.mov, 214MB. 1:47 min
360 Display SIGGRAPH 2007 Technical Video:
- 3Ddisplay.mov, 86.6MB. 4:45 min ( Quicktime ) - SIGGRAPH 2007 Technical Video
AWARDS:
| |
| 3D display receives "Best Emerging Technology" at SIGGRAPH 2007 |
PRESS COVERAGE:
- The display was highlighted at the opening of the new USC Stevens Institute for Innovation. The 3D Display made appearances in some of the resulting media coverage:
- Business Week article
- Los Angeles Times article, (requires login)
- CBS News, (video)
- Engadget.com, 8/31/2007, (video)
- The display was invited to Laval Virtual in April 2008. Here is some of the resulting press coverage:
- Sciences-Avenir article (in French)
- The display was invited to the FMX/08 conference in Stuttgart, Germany in May, 2008. Here is some of the resulting press coverage:
- Multimedia.de article (in German)
- flashconference 2008 blog
- VFXWorld article
- ESPN article
- WIRED Blog
- Giz Explains 3D Technologies