[C]NodeMCU(ESP8266)接入阿裡雲物聯網平台

阿裡雲物聯網平台公共執行個體，18元/年起： 點此購買

按用量付費6折起：

NodeMCU(ESP8266)接入阿裡雲物聯網平台

PIR隻有三個口，分别是VCC，GND和輸出口。接線方法如下（NodeMCU的D7相當于arduino裡的Pin 13）

物模型定義

C程式代碼

esp8266.ino 代碼

#include <ESP8266WiFi.h>
/* 依賴 PubSubClient 2.4.0 */
#include <PubSubClient.h>
/* 依賴 ArduinoJson 5.13.4 */
#include <ArduinoJson.h>

#define SENSOR_PIN    13

/* 連接配接您的WIFI SSID和密碼 */
#define WIFI_SSID         "路由器SSID"
#define WIFI_PASSWD       "密碼"


/* 裝置的三元組資訊*/
#define PRODUCT_KEY       "裝置PRODUCT_KEY"
#define DEVICE_NAME       "替換DEVICE_NAME"
#define DEVICE_SECRET     "替換DEVICE_SECRET"
#define REGION_ID         "cn-shanghai"

/* 線上環境域名和端口号，不需要改 */
#define MQTT_SERVER       PRODUCT_KEY ".iot-as-mqtt." REGION_ID ".aliyuncs.com"
#define MQTT_PORT         1883
#define MQTT_USRNAME      DEVICE_NAME "&" PRODUCT_KEY

#define CLIENT_ID         "esp8266|securemode=3,timestamp=1234567890,signmethod=hmacsha1|"
// 算法工具: http://iot-face.oss-cn-shanghai.aliyuncs.com/tools.htm 進行加密生成password
// password教程 https://www.yuque.com/cloud-dev/iot-tech/mebm5g
#define MQTT_PASSWD       "參考上面password教程，算法工具生成"

#define ALINK_BODY_FORMAT         "{\"id\":\"123\",\"version\":\"1.0\",\"method\":\"thing.event.property.post\",\"params\":%s}"
#define ALINK_TOPIC_PROP_POST     "/sys/" PRODUCT_KEY "/" DEVICE_NAME "/thing/event/property/post"

unsigned long lastMs = 0;
WiFiClient espClient;
PubSubClient  client(espClient);


void callback(char *topic, byte *payload, unsigned int length)
{
    Serial.print("Message arrived [");
    Serial.print(topic);
    Serial.print("] ");
    payload[length] = '\0';
    Serial.println((char *)payload);

}


void wifiInit()
{
    WiFi.mode(WIFI_STA);
    WiFi.begin(WIFI_SSID, WIFI_PASSWD);
    while (WiFi.status() != WL_CONNECTED)
    {
        delay(1000);
        Serial.println("WiFi not Connect");
    }

    Serial.println("Connected to AP");
    Serial.println("IP address: ");
    Serial.println(WiFi.localIP());

    
Serial.print("espClient [");


    client.setServer(MQTT_SERVER, MQTT_PORT);   /* 連接配接WiFi之後，連接配接MQTT伺服器 */
    client.setCallback(callback);
}


void mqttCheckConnect()
{
    while (!client.connected())
    {
        Serial.println("Connecting to MQTT Server ...");
        if (client.connect(CLIENT_ID, MQTT_USRNAME, MQTT_PASSWD))

        {

            Serial.println("MQTT Connected!");

        }
        else
        {
            Serial.print("MQTT Connect err:");
            Serial.println(client.state());
            delay(5000);
        }
    }
}


void mqttIntervalPost()
{
    char param[32];
    char jsonBuf[128];

    sprintf(param, "{\"idle\":%d}", digitalRead(13));
    sprintf(jsonBuf, ALINK_BODY_FORMAT, param);
    Serial.println(jsonBuf);
    boolean d = client.publish(ALINK_TOPIC_PROP_POST, jsonBuf);
    Serial.print("publish:0 失敗;1成功");
    Serial.println(d);
}


void setup() 
{

    pinMode(SENSOR_PIN,  INPUT);
    /* initialize serial for debugging */
    Serial.begin(115200);
    Serial.println("Demo Start");

    wifiInit();
}


// the loop function runs over and over again forever
void loop()
{
    if (millis() - lastMs >= 5000)
    {
        lastMs = millis();
        mqttCheckConnect(); 

        /* 上報 */
        mqttIntervalPost();
    }

    client.loop();
    if (digitalRead(SENSOR_PIN) == HIGH){
    Serial.println("Motion detected!");
    delay(2000);
      }
    else {
    Serial.println("Motion absent!");
    delay(2000);
  }

}           

PubSubClient.h 修改參數

運作效果