PIX7.0軟體的安裝及ASDM可視化管理軟體的安裝

pix 7.0支援的平台

Description 

PIX OS version 7.0(1) software. Requires a minimum of 16 MB Flash and 64 MB RAM. 

IMPORTANT: Read the Guide for Cisco PIX 6.2 and 6.3 Users Upgrading to Cisco PIX Software Version 7.0 and Release Note prior to downloading this release. 

PIX Security Appliance Operating System release 7.0 supports the following PIX models: 

515/515E

525

535

PIX software release 7.0 requires different amounts of RAM depending on the platform. 

PIX Security Appliance models 525 and 535 meet all RAM requirements for 7.0, 

no upgrades are necessary to run this software release on these platforms. 

Some PIX 515/515E systems may not meet the minimum requirements, and the purchase and installation of a 64MB RAM upgrade (Restricted license) or a 128MB RAM upgrade (Failover and Unrestricted licenses) may be necessary. 

For details refer to the Release Notes in the PIX 7.0 Documentation. 

（IOS為6.2及以下版本是用PDM，6.2以上版本使用ASDM）

二

更新7.0

1 進入monitor 更新7.0

2 進入正常模式 删除flash:pix701.bin

3 在正常模式下再更新pix701.bin即可

啟動進入rom下配置,pc網線連結pix1口，設定pc位址192.168.0.1，

interface 1

address 192.168.0.2

server 192.168.0.1

file pix701.bin

tftp

更新完成

三

在pix上安裝ASDM管理器

+++++++++++++Install Adaptive Security Device Manager (ASDM) +++++++++++++

down:http://www.cisco.com/pcgi-bin/tablebuild.pl/pix

pixfirewall# copy tftp flash

Address or name of remote host [0.0.0.0]? 

Source file name [cdisk]? 

Destination filename [asdm-501.bin]? 

The image is now copied over from the TFTP server to Flash. 

These messages appear and indicate that the transfer is a success. 

Accessing tftp://172.18.173.123/asdm-501.bin...

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!

Writing file flash:/asdm-501.bin...

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

!!!!!!!!!!!!!!!!!!!!

5880016 bytes copied in 140.710 secs (42000 bytes/sec)After the ASDM image is copied over, 

issue the asdm image flash: command in order to specify the ASDM image to use.

pixfirewall(config)# asdm image flash:asdm-501.bin

Save the configuration to Flash with the write memory command. 

pixfirewall(config)# write memory

This completes the ASDM installation process.

四

配置asdm

config asdm

interface Ethernet0

no sh

nameif outside

security-level 0

ip address 192.168.0.2 255.255.255.0 

!

interface Ethernet1

nameif inside

security-level 100

ip address 10.0.0.1 255.255.255.0 

hostname pixfirewall

domain-name domain

asdm image flash:/asdm-501.bin

asdm history enable

http server enable          //這一步必須要設定。

http 192.168.0.1 255.255.255.255 outside    

              //如果希望任何IP都能從外網口管理ASDM，可以使用：http 0 0 outside 指令。如果沒有這條指令，任何IP将都無法通路和管理ASDM。

用asdm管理pix

https://192.168.0.1

結束

本文轉自 qq8658868 51CTO部落格，原文連結：http://blog.51cto.com/hujizhou/1186360，如需轉載請自行聯系原作者